Becker BE A00 Operating Manual Download Page 33

Page: 33 / 155

GENERAL OPERATION

>>>

> D

> GB

> F

> I

> PL

Press the remote control onto the
base plate.

Hold the bottom part of the remote
control and turn the remote control
clockwise until it locks into place.

Removing the remote control

You can remove the remote control
again, to change the battery for example.

Hold the bottom part of the remote
control and turn the remote control
anti-clockwise until it becomes
detached from the base plate.

Connecting the remote control to the

Navigation device

Connecting for the first time

Switch on the Navigation device.

Press the button

on the remote

control.

The connection to the Navigation device
is established.

Notice:

The car adapter cable with radio remote
control receiver must be connected to
the cigarette lighter and navigation sys-
tem and be supplied with power. The ra-
dio receiver is in the plastic case on the
cable.

Summary of Contents for BE A00




























































































































































Search results

Summary of Contents for BE A00

Reviews:

Related manuals for BE A00

Brands by name

Popular brands

Becker BE A00, Operating Manual

Search results

Summary of Contents for BE A00

Reviews:

Related manuals for BE A00

Brands by name

Popular brands