Beam ECG Operating Manual Download

Page: 45 / 76

Beam®, Operating Manual, Rev. 4.6.1 01/2016, GmbH

Hypertension-Management-Software Client-Server

4.10 Analyse Recordings

Initial Situation:

You have already read the ECG recordings from the recorder

and saved them to the HMS CS (see

4.7, Read out recordings from the Recorder

Beam

The following functions are available for the analysis of ECG recordings:

■

Set filter and zoom

■

Show and hide conductions

■

Measuring the ECG using the mouse pointer

■

Add comment

■

4.10.1 Set filter and zoom

►

Display the desired patient (see

4.6.2, Select already created patient

►

In the working window click on the

ECG

tab.

The

ECG tab

contains a list of already transferred recordings on the left side.

►

Click on a measurement.

The belonging ECG will be displayed.

►

For the determination of the dimensions of the displayed extract and the filter

go to the following field on the lower left side of the ECG

and specify the axis units in mm/s and mm/mV.

Summary of Contents for ECG













































































Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands

Beam ECG, Operating Manual

Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands