Beam ECG Operating Manual Download

Page: 15 / 76

Beam®, Operating Manual, Rev. 4.6.1 01/2016, GmbH

3. Product Description

(one-time coupling of both interfaces) by pressing and holding of the start

button and the insertion of the battery at the same time. When the device is

paired the start button has to be pressed for 5 seconds in order to access the

communication mode.

■

Prepare the recorder using the desired settings via the HMS CS (see chapter

4.8).

■

If you use single-use electrodes you can now put the electrode cable into the

port of the device. The recorder detects the cable and an audible signal will

sound.

■

After the preparation of the patient the control recording is carried out (training).

The ECG recording can be transferred in real-time to the HMS CS via Bluetooth.

Patient and staff receive an immediate overview of the correct positioning of

the electrodes on the chest wall. When using the device electrodes, the correct

positioning and the correctly applied pressure can be determined and indicated

to the patient. Follow the description in chapter 4.8.7

■

The device can be carried on the belt using the provided bag.

■

Finally the patient should be informed about the carry-period, the replacement of

electrodes and batteries and the triggering of ECG recordings.

■

In case you are using the case electrodes on the back of the device, please

consider the conduction displayed in the following figure. The device is posi-

tioned on the chest with the start button facing up.

Figure 3.2: Conductions of case delectrodes - Reverse of

Beam

Summary of Contents for ECG













































































Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands

Beam ECG, Operating Manual

Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands