Beam ECG Operating Manual Download Page 61

Page: 61 / 76

Beam®, Operating Manual, Rev. 4.6.1 01/2016, GmbH

Hypertension-Management-Software Client-Server

►

Specify the desired settings.

►

Click on

The window disappears.

4.13.9 GDT Settings

GDT (Device data transfer) is a data exchange format, which is used in the German

healthcare system by the established medical doctors. The GDT interface serves

for the system independent data transfer between medical measuring devices and

a practice computer system.
The GDT settings are required for the automatic exchange of patient data between

your practice and the HMS CS. If the correct settings are made here the HMS CS

can start your practice software and load the patient data directly from it.

►

In the taskbar click on

Settings

and then on

GDT Settings

The GDT settings window appears.

Summary of Contents for ECG













































































Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands

Beam ECG, Operating Manual

Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands