Beam ECG Operating Manual Download

Page: 42 / 76

Beam®, Operating Manual, Rev. 4.6.1 01/2016, GmbH

Hypertension-Management-Software Client-Server

4.8.8 Complete recorder preparation

►

Click on

The

prepare recorder

window disappears and the recorder cancels the Bluetooth

connection with an audible signal.

4.8.8 Activate recording mode of ECG Recorder Beam

After you finished the preparations of the recorder in the HMS CS program the

recorder can be put into the bag and attached to a belt on the patient.

The recorder is activated automatically when the batteries are inserted and no

Bluetooth connection is active.

4.9 Read out recordings from recorder

If you have not worked with the e-health service and already have received the recor-

dings telemetrically you can read out the recordings via the Bluetooth interface.
The following steps are processed:

Connect the HMS CS with the recorder, see

4.7 Connection via Bluetooth

Transfer recordings from recorder, see

4.7, Read recordings from ECG

Recorder Beam

via Bluetooth

►

Start the HMS CS program.

Assuming the respective program settings the

Patient List

window appears (see

4.13.8, Options

). In this case select any patient (see

4.6.2, Select already cre-

ated patient

►

Bring your ECG Recorder Beam

into the communication mode by pressing

and holding for 3 seconds.

►

The HMS CS program checks if a patient ID is available on the recorder.

If yes

If not

A prompt appears:

The patient-ID in the

measuring device (XXX) corresponds to

XXX. Should the series of measurements

be assigned to the patient?

►

Click on

►

Select the desired patient, see

4.6.2, Select already created

patient

The recordings are transferred to the HMS CS program and saved to the patient.

A window with the following information appears: XXX measurements transferred.
Click on

A window with the following prompt appears: There are still series of measurements

saved in this recorder. Should the series of measurements be deleted?

Summary of Contents for ECG













































































Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands

Beam ECG, Operating Manual

Search results

Summary of Contents for ECG

Reviews:

Related manuals for ECG

Brands by name

Popular brands