Beam ECG Operating Manual Download Page 7

Page: 7 / 76

Beam®, Operating Manual, Rev. 4.6.1 01/2016, GmbH

1. Introduction

1.1 Preamble

With this

ECG Loop-/Event Recorder

Beam

, you own a state of the art system.

The ECG Loop-/Event Recorder can be prepared for a new patient in a practice

within a few minutes and can therefore be integrated into the daily operation of

the practice quickly.
Additionally to the known Loop/Event recording the recorder also provides the

option to send recordings via the mobile network and to inform the physician

about incoming readings. The patient does not need to appear in the practice for

the analysis. Only after receipt of a qualitatively sufficient reading an appointment

is setup with the patient.

1.2 About this Operating Manual

This operating manual will make you quickly familiar with the use of the ECG Loop-/

Event Recorder and its accessories. After a little practicing you will learn how easily

the ECG Loop-/Event Recorder Beam

can be operated.

For the management of the ECG Loop-/Event Recorder Beam

, I.E.M GmbH offers

the following Software:

■

Hypertension-Management-Software Client-Server Data Management

(HMS CS) Version 3.0 or higher.

■

The Loop/Event Recorder Beam

cannot be used without the HMS CS.

References to specific version characteristics only apply to the the relevant parts

of the respective version.

Important

: The operating manual describes the ECG Loop-/Event Recorder

Beam

and the accessories in the order in which you start to operate

the device and use it later on. The general explanation, the installation,

launch, and reading preparation, is followed by the setup of the patient

and analysis. The individual functions will only be explained when

they are needed. This way you will be introduced to the Loop/Event

Recorders Beam

step-by-step.

The operating manual must always be available to the user.

1.3 Classification

The ECG Loop/Event-Recorder Beam

is a medical device of the class IIa accord-

ing to Rule 10, Annex IX, Directive 93/42EEC.

1.4 CE Sign

The Beam

meets the requirements for the Medical Device Directive

93/42/EEC and carries the CE sign.
The Beam

meets the requirements of the R&TTE Directive 1999/5/EC

and carries the CE-sign.

Summary of Contents for ECG













































































Search results

Summary of Contents for ECG

Reviews:

Brands by name

Popular brands

Beam ECG, Operating Manual

Search results

Summary of Contents for ECG

Reviews:

Brands by name

Popular brands