Baxi PBS-i WH2 Series User Manual Download Page 93

Page: 93 / 180

6.6.6

Evacuation

1. Check that the A and B / C stop valves are closed.

2. Connect the vacuum gauge and the vacuum pump to the service

connection on A stop valve.

3. Produce a vacuum in the indoor module and the refrigerant

connection pipes.

4. Check the pressure using the recommendations table below:

Tab.26

Outdoor temperature °C

≥ 20

- 10

Pressure to be

reached

(bar)

1000

(0.01)

600

(0.006)

250

(0.0025

)

200

(0.002)

Evacuation time after

reaching the pressure h

5. Close the valve between the vacuum gauge / vacuum pump and A

stop valve.

6. After shutting off the vacuum pump, immediately open the valves.

6.6.7

Opening the valves

1. Remove the cap from the refrigerant fluid stop valve, fluid end.

2. Open valve A with a hexagonal spanner by turning anti-clockwise until

it stops.

3. Put the cap back in place.

4. Remove the cap from refrigerant gas stop valve B or C.

5. Open the valve.

Valve B

Open the valve with pliers by turning it a quar

ter turn anti-clockwise.

Valve C

Open the valve with a hexagonal spanner by

turning anti-clockwise until it stops.

6. Put the cap back in place.

7. Disconnect the vacuum gauge and the vacuum pump.

8. Put the cap back in place on valve A.

9. Tighten all the caps with a torque wrench with a torque load of 20 to

25 N·m.

10. Check the leak-tightness of the connections using a leak detector.

11. If the refrigeration pipes are more than 10 metres long, add the

required quantity of refrigerant fluid.

6.7

Electrical connections

6.7.1

Recommendations

Warning

Only qualified professionals may carry out electrical

connections, always with the power off.

Earth the appliance before making any electrical connections.

Make the electrical connections on the appliance in accordance with the

requirements of the prevailing standards,

Make the electrical connections on the appliance in accordance with the

information given in the electrical schematics delivered with the

appliance,

Fig.44

MW-M002499-2

Fig.45

MW-M002295-2

6 Installation

7706696 - v04 - 11102018

AWHP-2 PBS-i

Summary of Contents for PBS-i WH2 Series





















































































































































































Search results

Summary of Contents for PBS-i WH2 Series

Reviews:

Baxi PBS-i WH2 Series, User Manual, Page: 93 / 180

Search results

Summary of Contents for PBS-i WH2 Series

Reviews: