manualshive.com logo in svg

Baxi PBS-i WH2 Series, User Manual, Page: 150 / 180

Share
Download
Baxi PBS-i WH2 Series User Manual Download Page 150

Error

code

Message

Description

H02.03

Conf Error 

Configuration Error

The configuration parameters entered are incorrect.

Configure CN1 / CN2 depending on the output of the outdoor unit installed (CNF 

menu).

H02.04

Parameter Error

Parameter Error

Restore the factory settings.

If the error is still present: change the central unit PCB.

H02.05

CSU CU mismatch

CSU does not match CU type

Software change (software number or version parameter inconsistent with the mem­

ory).

H02.07

Water Press Error 

Water Pressure Error active

Check the hydraulic pressure in the heating circuit.
Check the wiring between the central unit PCB and the pressure sensor.

Check the connection of the pressure sensor.

H02.09

Partial block 

Partial blocking of the device recognized

BL input on the central unit PCB terminal block open

Check the contact on the BL input.

Check the wiring.

Check the AP001 and AP100. parameters.

H02.10

Full Block 

Full blocking of the device recognized

BL input on the central unit PCB terminal block open

Check the contact on the BL. input.

Check the wiring.

Check the AP001 and AP100. parameters.

H02.23

System flow error 

System water flow error active

Flow problem

Insufficient flow: open a radiator valve.

The circuit is clogged:

Check that the filters are not obstructed and clean them if necessary.

Clean and flush the installation,

No circulation:

Check that the valves and thermostatic valves are open,

Check that the circulating pump is working,

Check the wiring,

Check the pump supply: if the pump does not work, replace it.

Too much air: completely vent the indoor module and the installation for optimum run­

ning.

Incorrect wiring: check the electrical connections.

Flow meter:

Check the electrical connections and the direction of the flow meter (arrow to the 

right).

Replace the flow meter if necessary

H02.25

ACI error

Titan Active System short circuited or on an open circuit

Check the connection cable.

Check that the anode has not short-circuited and is not broken.

H02.36

Funct device lost

Functional device has been disconnected

No communication between the central unit PCB and the additional circuit PCB

Check the connection of the supply cable between the PCBs.

Check the connection of the BUS cable between the PCBs.

Run automatic detection.

H02.37

Uncritic device lost

Uncritical device has been disconnected

No communication between the central unit PCB and the additional circuit PCB

Check the connection of the supply cable between the PCBs.

Check the connection of the BUS cable and the PCBs.

Run automatic detection.

11 Troubleshooting

102

AWHP-2 PBS-i

7706696 - v04 - 11102018

Summary of Contents for PBS-i WH2 Series





















































































































































































Reviews:

No comments