Baxi PBS-i WH2 Series User Manual Download Page 138

Page: 138 / 180

Parameter

Description

Unit

EHC-04

SCB04-B

AM012

Current main status of the appliance.

See

Control system sequence chapter

AM014

Current sub status of the appliance.

See

Control system sequence chapter

AM015

Is the pump running?

AM016

Flow temperature of appliance.

°C

AM019

Water pressure of the primary circuit.

bar

AM027

Instantaneous outside temperature

°C

AM040

Temperature used for hot water control algorithms.

°C

AM056

Wate flow rate in the system

l/min

AM091

Seasonal mode active (summer / winter)

0: Winter

1: Frost protection

2: Summer neutral band

3: Summer

AM101

Internal system flow temperature setpoint

CM030

Measure of the Room temperature of the zone

°C

CM040

Measure Zone Flow Temperature or DHW

temperature

°C

CM060

Current Pump speed of zone

CM120

Zone Current Mode:

0 =Scheduling
1 =Manual

2 =Antifrost

3 =Temporary

CM130

Current activity of the zone:

0 =Anti frost

1 =Reduced

2 =Comfort

3 =Anti legionella

CM190

Wished room temperature setpoint of the zone

°C

CM210

Current Outside Temperature of the zone

°C

DM001

Domestic Hot Water tank temperature (bottom sensor) °C

DM006

Domestic Hot Water tank temperature (top sensor)

DM009

Automatic/derogation status of Domestic Hot Water

mode:

0 =Scheduling

1 =Manual

2 =Antifrost

3 =Temporary

°C

DM029

Domestic Hot Water temperature setpoint

°C

HM001

Heat pump flow temperature after condenser

°C

HM002

Heat pump return temperature after condenser.

°C

HM033

Flow temperature setpoint in cooling mode

°C

HM034

Heat pump PCU backup flow temperature

°C

not used

HM035

Heat pump PCU backup return temperature

°C

not used

HM036

Heat pump PCU backup domestical hot water

temperature

°C

not used

HM037

Heat pump PCU back up Internal Setpoint

°C

not used

HM038

Heat pump PCU back up status

not used

HM039

Heat Pump PCU back up Sub Status

not used

9 Settings

AWHP-2 PBS-i

7706696 - v04 - 11102018

Summary of Contents for PBS-i WH2 Series





















































































































































































Search results

Summary of Contents for PBS-i WH2 Series

Reviews:

Baxi PBS-i WH2 Series, User Manual, Page: 138 / 180

Search results

Summary of Contents for PBS-i WH2 Series

Reviews: