Baxi PBS-i WH2 Series User Manual Download Page 124

Page: 124 / 180

ADV parameter

Description of the ADV advanced parameters

Factory setting

EHC–04

HP079

Maximum offset applied on the dynamic cooling setpoint when a 0-10V humidity

sensor is used

Can be set from 0 to 15°C

HP086

Activation of hydraulic management mode for the configuration with a low-loss

header, or for a buffer tank connected as a low-loss header

0 =No

1 =Yes

HP087

Buffer tank hysteresis to start and stop heating

Can be set from 0 to 30 °C

HP091

Offset temperature of heating setpoint when photovoltaic function is activated

Can be set from 0 to 30 °C

HP092

Offset temperature of DHW setpoint when photovoltaic function is activated

Can be set from 0 to 30 °C

HP094

Start time of the low noise when function activated

Can be set from 00:00 to 23:59

Value accepted when HP058 = 1

22:00

HP095

Stop time of the low noise when function activated

Can be set from 00:00 to 23:59.

Value accepted when HP058 = 1

06:00

HP108

Activation time delays for the back-ups between stage 1 and stage 2 (electrical

back-up) in central heating mode

PP016

Maximum central heating pump speed (%)

Maximum pump speed in heating mode

Can be set from 20 to 100%

100%

PP018

Minimum central heating pump speed (%)

Minimum pump speed in heating mode

Can be set from 20 to 100%

30%

Auto detect

available

CNF

Reset factory parameters

See the data plate

ADV

ADV advanced parameters

not available

9.3

Setting the parameters

9.3.1

Language selection

1. Access the User menu.

2. Select the HMI sub-menu.

3. Select the AP103 parameter corresponding to language selection by

pressing the or keys.

4. Confirm by pressing the

key.

Fig.97

-5

-2

9 Settings

AWHP-2 PBS-i

7706696 - v04 - 11102018

Summary of Contents for PBS-i WH2 Series





















































































































































































Search results

Summary of Contents for PBS-i WH2 Series

Reviews:

Baxi PBS-i WH2 Series, User Manual, Page: 124 / 180

Search results

Summary of Contents for PBS-i WH2 Series

Reviews: