manualshive.com logo in svg

Baxi PBS-i WH2 Series, User Manual, Page: 151 / 180

Share
Download
Baxi PBS-i WH2 Series User Manual Download Page 151

Error

code

Message

Description

H02.60

Unsupported function

The zone doesn't support the selected function

H06.01

HP Unit Failure

Heat Pump Unit Failure occured

Heat pump outdoor unit fault

Check the wiring between the central unit PCB and the communication bus on the 

outdoor unit.

Check the connection of the communication cable between the central unit PCB and 

the interface PCB.

Check the connection of the supply cable between the central unit PCB and the in­

terface PCB.

Check the connection of the outdoor unit supply cable.

11.2.2  Fault codes

If a fault code is still present after several automatic start-up attempts, the 

heat pump switches to error mode.
The heat pump will only resume normal operation once the causes of the 

fault have been eliminated by the installer.
As a result of:

a manual reset,

a reset by a maintenance message.

Tab.79 List of fault codes

Error

code

Message

Description

E00.00

TFlow Open

Flow temperature sensor is either removed or measures a temperature below range

E00.01

Flow temp sensor 

shorted or above range

Flow temperature sensor is either shorted or measures a temperature above range

E02.13

Blocking Input

Blocking Input of the Control Unit from device external environment

Input BL open.

Check the wiring.

Check the component connected to the BL. contact

Check the component connected to the AP001 and AP100. contact

E02.24

System flow locking 

active

System water flow locking active

Insufficient flow: open a radiator valve

The circuit is clogged:

Check that the filters are not obstructed and clean them if necessary.

Clean and flush the installation.

No circulation:

Check that the valves and thermostatic valves are open.

Check that the filters are not obstructed.

Check that the circulating pump is working.

Check the wiring.

Check the pump supply: if the pump does not work, replace it.

Too much air

Completely vent the indoor module and the installation for optimum running.

Check that the automatic air vents are properly open (also check the hydroblock).

Completely vent the indoor module and the installation for optimum running.

Incorrect wiring: check the electrical connections.

Flow meter:

Check the electrical connections and the direction of the flow meter (arrow to the 

right).

Replace the flow meter if necessary.

11 Troubleshooting

7706696 - v04 - 11102018

AWHP-2 PBS-i

103

Summary of Contents for PBS-i WH2 Series





















































































































































































Reviews:

No comments