Baxi PBS-i WH2 Series User Manual Download Page 137

Page: 137 / 180

Live

Operating description

Heating only. When the DP120 differential is reached, domestic hot water production is triggered.

If there is not enough domestic hot water (e.g. if the domestic hot water does not heat up quickly

enough): reduce the trip differential (hysteresis) by modifying the value of the DP120 parameter. The

DHW tank will then heat up the water more quickly.

Domestic hot water production only.

9.5.3

Running the back-up in domestic hot water mode

Start-up conditions for the back-up

The start-up conditions for the back-up producing domestic hot water are

described in the following table.

Tab.72

Parameter

Setting

AP001

The function of the BL1 blocking input is not set to 4, 6 or 8

AP100

The function of the BL2 blocking input is not set to 4, 6 or 8

Operating description

The behaviour of the hydraulic or electrical back-up in domestic hot water

mode depends on the configuration of the DP051 parameter.

Tab.73 Behaviour of the hydraulic or electrical back-up

Value of the parameter

DP051

Operating description

The system gives priority to the heat pump during domestic hot water production.

Recourse to the hydraulic or electrical back-up is only taken if the DP090 time delay has elapsed in

domestic hot water mode, unless hybrid mode is activated. In that case, hybrid logic takes over.

Domestic hot water production mode gives priority to comfort by accelerating domestic hot water pro

duction by simultaneously using the heat pump and the hydraulic or electrical back-up.

In this mode, there is no maximum time for domestic hot water production as the use of the back-ups

helps to ensure domestic hot water comfort more quickly.

9.6

Reading out measured values

The measured values are available in the Information menu of the

different PCBs.
Certain parameters are displayed:

according to certain system configurations,

according to the options, circuits or sensors actually connected.

Tab.74 Choosing the menu

Counters

Selection

Measured values on circuit A

Choose menu EHC-04

Measured values on circuit B

Choose menu SCB04-B

Measured values connected to the

operation of the heat pump

Choose menu EHC-04

Tab.75 Values available (X) in the sub-menus EHC-04, SCB04-B

Parameter

Description

Unit

EHC-04

SCB04-B

AM002

"Silent mode" status

AM010

The current pump speed

9 Settings

7706696 - v04 - 11102018

AWHP-2 PBS-i

Summary of Contents for PBS-i WH2 Series





















































































































































































Search results

Summary of Contents for PBS-i WH2 Series

Reviews:

Baxi PBS-i WH2 Series, User Manual, Page: 137 / 180

Search results

Summary of Contents for PBS-i WH2 Series

Reviews: