manualshive.com logo in svg

Baxi PBS-i WH2 Series, User Manual, Page: 103 / 180

Share
Download
Baxi PBS-i WH2 Series User Manual Download Page 103

Tab.37 Control parameter for the OT input on the R-Bus terminals

Parameter

Description

CP640

Configuration of the contact direction of the OT input for heating mode.

CP690

Reversal of the direction of the logic in cooling mode compared to heating mode

Tab.38 Default settings for the CP640 and CP690 parameters

Value of the CP640 parame­

ter

Value of the CP690 parame­

ter

Heating if the OT contact is

Cooling if the OT contact is

1 (Default value)

0 (Default value)

closed

closed

0

0

open

open

1

1

closed

open

0

1

open

closed

6.8.2 

Connecting a thermostat with heating/cooling contact

The AC thermostat is only connected to the R-Bus and BL1 terminals of 

the EHC–04 PCB, with a single heating circuit.
The PCBs are delivered with a bridge on the R-Bus input.

Tab.39

Value of 

the param­

eter

CP640

Value of 

the param­

eter 

AP098

Blocking input 

status

BL1

Operating mode 

for the heat 

pump

If R-Bus contact open

If R-Bus contact closed

1

(default 

value)

1

(default 

value)

Open

Cooling

No cooling demand

Cooling demand

1

(default 

value)

1

(default 

value)

Closed

Heating

No heating demand

Heating demand

1

0

Open

Heating

No heating demand

Heating demand

1

0

Closed

Cooling

No cooling demand

Cooling demand

0

1

Open

Cooling

Cooling demand

No cooling demand

0

1

Closed

Heating

Heating demand

No heating demand

0

0

Open

Heating

Heating demand

No heating demand

0

0

Closed

Cooling

Cooling demand

No cooling demand

1. Connect the "heating/cooling" thermostat contact to the BL1 input on 

the EHC–04 PCB for the heat pump.

2. Connect the "On/Off" thermostat contact to the R-Bus input on the 

EHC–04 PCB for the heat pump.

3. In the Installer/EHC–04 menu, configure the BL1 input to "Heating/

Cooling", by setting the AP001 parameter to 11.

4. In the Installer/EHC–04 menu, set the contact direction of the BL1 

input with the AP098 parameter.

5. In the Installer/CIRCA0 menu, set the contact direction of the R-Bus 

input with the CP640 parameter.

6.9 

Filling the installation

6.9.1 

Filling the heating circuit

Before filling the heating system, flush it thoroughly.

6  Installation

7706696 - v04 - 11102018

AWHP-2 PBS-i

55

Summary of Contents for PBS-i WH2 Series





















































































































































































Reviews:

No comments