manualshive.com logo in svg

Baxi PBS-i WH2 Series, User Manual, Page: 86 / 180

Share
Download
Baxi PBS-i WH2 Series User Manual Download Page 86

4. Ensure the support meets the following specifications: 

Specifications

Examples

Flat surface that can support the 

weight of the outdoor unit and its ac­

cessories

Concrete base,

Sill,

Concrete blocks,

No rigid connection to the building served to avoid the transmission of vibration

Sufficient above ground elevation 

(100 to 500 mm) to keep it above 

water

Base with a metal frame to allow condensates to be discharged correctly.

The width of the base must not exceed the width of the outdoor unit.

The condensates discharge must be regularly cleaned in order to prevent any block­

ages

6.4.3 

Choosing the location of a noise abatement screen

When the outdoor unit is too close to neighbours, a noise abatement 

screen can be fitted to reduce noise pollution.

Fig.33

MW-C000373-1

Brrrrr....

Brrrrr....

Br

rrr

r...

.

Brrrrr....

1. Locate the noise abatement screen as close as possible to the source 

of noise whilst allowing for the free circulation of air in the exchanger 

on the outdoor unit and maintenance work.

2. Respect the minimum positioning distances of the outdoor unit from 

the noise abatement screen.

6.4.4 

Selecting the location of the outdoor unit in cold and 

snowy regions

Wind and snow can significantly reduce the performance of the outdoor 

unit, the location of the outdoor unit must meet the following conditions.

Fig.34

MW-6000252-2

1

2

3

/

4

1. Install the outdoor unit sufficiently high off the ground to allow 

condensates to be discharged correctly.

6  Installation

38

AWHP-2 PBS-i

7706696 - v04 - 11102018

Summary of Contents for PBS-i WH2 Series





















































































































































































Reviews:

No comments