Baxi PBS-i WH2 Series User Manual Download Page 117

Page: 117 / 180

Tab.45

Parameter

Description

Factory setting

CIRCA

Factory setting

CIRCB

CP000

Maximum Flow Temperature setpoint zone

For circuit A: Can be set from 7 °C to 100 °C

Electrical back-up:

Hydraulic back-up:

CP020

Type of circuit A, connected to the EHC–04 PCB:

0 = heating circuit deactivated

1 = radiators. Cooling not possible.

2 = underfloor heating. Cooling possible.

3 = not available

4 = not used

5 = convection fan. Cooling possible.

Type of circuit B, connected to the SCB-04 PCB:

0 = heating circuit deactivated

1 = radiators. Cooling not possible.

2 = underfloor heating with mixing valve. Cooling possible.

3 =Swimming pool

4 = not used

5 = convection fan. Cooling possible.

6 and above = not used

CP030

Bandwith of mixing valve zone where modulation takes place.

Can be set from 4 °C to 16 °C

not available

CP040

Pump post runtime of the zone

Can be set from 0 Min to 20 Min

CP050

Shift between calculated setpoint and mixing valve circuit

setpoint

Can be set from 0 °C to 16 °C

not available

CP060

Wished room zone temperature on holiday period

Can be set from 5 °C to 20 °C

CP070

Max RoomTemperature limit of the circuit in reduced mode,

that allows switching to comfort mode

Can be set from 5 °C to 30 °C

CP210

Comfort footpoint of the temperature of heat curve of the circuit

can be set from 16 to 90 °C

set to 15 = the curve base temperature is set automatically

and is the same as the room set point temperature

CP220

Reduced footpoint of the temperature of heat curve of the

circuit

can be set from 6 to 90 °C

set to 15 = the curve base temperature is set automatically

and is the same as the room set point temperature

CP230

Heating curve temperature gradient of the zone

Can be set from 0 to 4

0.7

CP240

Adjustment of the influence of the zone room unit

Can be set from 0 to 10

CP270

Mixing flow temperature setpoint cooling of the zone

Can be set from 11 °C to 23 °C

CP280

Fan flow setpoint cooling of the zone

Can be set from 7 °C to 23 °C

CP340

Type of Reduced Night Mode, stop or maintain heating of

circuit

0 =

Stop heat demand

1 = Continue heat demand

9 Settings

7706696 - v04 - 11102018

AWHP-2 PBS-i

Summary of Contents for PBS-i WH2 Series





















































































































































































Search results

Summary of Contents for PBS-i WH2 Series

Reviews:

Baxi PBS-i WH2 Series, User Manual, Page: 117 / 180

Search results

Summary of Contents for PBS-i WH2 Series

Reviews: