manualshive.com logo in svg

Baxi PBS-i WH2 Series, User Manual, Page: 21 / 180

Share
Download
Baxi PBS-i WH2 Series User Manual Download Page 21

5.3 

Shutdown

5.3.1 

Switching off the heating

Important

Heating mode can be managed via the TIME PROG sub-menu 

dedicated to timer programming.

Important

If the heating function is shut off, then the cooling will also be shut 

off.

1. Go to stop mode by pressing the 

 key. 

2. Select the heating mode by pressing the   key. 
3. Confirm by pressing the 

 key.

4. Select the heating shut-down pressing the   key. 

The screen displays:      .

The frost protection function continues to run.

The heating and cooling have been shut down.

Important
Press the   key to restart the appliance: the screen will 
display    .

5. Confirm by pressing the 

 key.

6. Go back to the main display by pressing the 

h

 key. 

Important

The display disappears after a few seconds of inactivity.

5.3.2 

Shutting down the cooling function

Important

If the heating function is shut off, then the cooling will also be shut 

off.

1. Access the   menu.
2. Confirm access by pressing the 

 key.

3. Select CIRCA or CIRCB by pressing the   or   key.
4. Confirm the selection by pressing the 

 key.

5. Select TP.C by pressing the   or   keys.
6. Confirm the selection by pressing the 

 key.

7. Modify the timer program to stop cooling.

Fig.22

MW-5000027-4

Fig.23

MW-5000133-3

Fig.24

MW-5000134-3

5  Operation

7706698 - v04 - 17102018

AWHP-2 PBS-i

21

Summary of Contents for PBS-i WH2 Series





















































































































































































Reviews:

No comments