B&D Panelift B&D Storm-Shield PFI Installation Instructions Manual Download Page 29 | Manualshive

Page: 29 / 32

background image

NOTE

: In coffin garages (those with no access other

than the garage door), the lock handle should be
installed immediately after fitting the lock panel.

The lock handle is to be fixed to the middle of the
second panel. Using lock plate as a guide, centre on
central end stile and drill through the end stile and the
panel using a 1/2” (13 mm) drill bit for the large hole
and a 3/16”(5 mm) bit for the two holes on either side.

Fit the “T” handle to the panel by inserting the lock
shaft and the two 3/16” thread bolts into the panel
from the outside, through the lock muntin. Attach
the 3/16” or 4.7 mm nuts and washers securing the
‘T’ Handle in place. Next insert the lock guide plate
(dimples facing away from door) followed by the
internal handle, the lock cam and the second guide
plate (dimples facing the door). Lock together with
3/16” nuts and washers, see Figure 3.1.2.

Lock Strikes

External Lock

Handle

Internal Lock

Handle

Lock Cam

Lock Guide Plates

Lock Cable

Washer

Nuts

Lock Catch

FIGURE 3.1.1 PARTS

FIGURE 3.1.2 LOCK ASSEMBLY

External Lock Handle

Lock Guide Plate

Internal Lock Handle

Lock Cam

Lock Washer

Nut 4mm

Lock Guide Plate

3.0 OPTIONAL COMPONENTS

3.1 LOCK INSTALLATION (PFT & PFI ONLY)

NOT SUITABLE FOR

B&D STORM-SHIELD

™

29

panelift

®

pFT, panelift

®

Icon

™

pFI, b&D Storm-Shield

™

pFI and Insul-Shield

™

Installation Instructions

Revision 9 - March 2016

«
...
27
28
29
30
31
...
»

Summary of Contents for Panelift B&D Storm-Shield PFI

































Reviews:

No comments

Related manuals for Panelift B&D Storm-Shield PFI

Brand: fadini Pages: 12

Brand: fadini Pages: 12

Brand: fadini Pages: 12

Brand: fadini Pages: 16

Brand: Assa Abloy Pages: 40

Brand: Telcoma Pages: 16

Brand: Telcoma Automations Pages: 24

Brand: Craftsman Pages: 16

Brand: Craftsman Pages: 34

Brand: Craftsman Pages: 24

Brand: Craftsman Pages: 84

Brand: Craftsman Pages: 100

Brand: Craftsman Pages: 56

Brand: Craftsman Pages: 100

Brand: FAAC Pages: 32

Brand: SOMFY Pages: 68

SlideSmart CNX 15

Brand: Nice Pages: 48

Brand: tau Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands