B&D Panelift B&D Storm-Shield PFI Installation Instructions Manual Download Page 13 | Manualshive

Page: 13 / 32

background image

If installing taper please consult page 30. Open up the pack of
door panels making sure the bottom panel (weather strip seal
on the bottom of the panel and bottom Hinge Hole see Figure
2.3.1) is on top of the pack.

Bottom Panel:

Locate both bottom hangers and cables. Insert

cable through the holes of the bottom hanger as shown in
Figure 2.3.2A. Remove existing screws in the two bottom
corners of the panel near the weather strip and discard, see
Figure 2.3.2b. Attach the bottom hangers to the lower end of
the door using 6 TEK screws in each as shown in Figure 2.3.2C.

Insert the polyethylene hinge links into the recesses of the top

of the panel and fix into place using the white pins. Insert four
wheels and axles into the top of the panel (white pins) and the
bottom of the panel (grey block). Insert appropriate wheels
and axles, Figure 2.3.2C & 2.3.3.

Ensure the axles are lightly

lubricated with lithium grease before inserting.

Insulated Insul-Shield

™

:

Hinge links are in two pieces and clip

together when inserted. After the next panel has been lowered
in place a special screw is inserted to hold in place as shown
in Figure 2.3.3.

Middle Panels:

Repeat the process for fitting links, pins and

wheels and axles to the top of each middle panel.

FIGURE 2.3.2

Secure hanger

using 6 TEK

screws to each

A

B

C

PARTS USED

FIGURE 2.3.1

Hinge pin

Hinge Links

bottom Hangers

(left hand- right hand)

2 Lifting Cable

(variable)

Standard

bottom

black Hinge

Other

panels

wheel Axles

Smooth-Track™

Insul-Shield™

2.3 ASSEMBLING BOTTOM & MIDDLE PANELS

FIGURE 2.3.3

FITTING THE INSULATED DOOR

SPLIT LINK FROM INSIDE

1. Click the male section of the link

marked TOp in first. Ensure TOp
is facing you from inside looking
out.

2. Insert the female part to the male

and click together.

3. The screw is fitted after the next

panel has been placed onto the
link via the hole provided.

bottom Grey Hinge

with Offset

bottom

panels

weather

strip

13

panelift

®

pFT, panelift

®

Icon

™

pFI, b&D Storm-Shield

™

pFI and Insul-Shield

™

Installation Instructions

Revision 9 - March 2016

«
...
11
12
13
14
15
...
»

Summary of Contents for Panelift B&D Storm-Shield PFI

































Reviews:

No comments

Related manuals for Panelift B&D Storm-Shield PFI

Brand: 4Ddoors Pages: 3

Brand: 4Ddoors Pages: 36

Brand: Chamberlain Pages: 2

Brand: Accessmatic Pages: 39

Brand: GBD Pages: 28

Brand: FAAC Pages: 14

Brand: Key Automation Pages: 38

Brand: NRG Automation Pages: 14

Brand: Life Pages: 35

Brand: Cardin Elettronica Pages: 44

Brand: Cardin Pages: 52

Brand: Cardale Pages: 6

Brand: TOPP Pages: 56

CCO-50NC Series

Brand: CUISINEART Pages: 6

Brand: Wallace International Pages: 28

T-MODE TM 45 P&P

Brand: FAAC Pages: 12

Essentials KEC10

Brand: Kambrook Pages: 4

Brand: GATEXPERT Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands