B&D Panelift B&D Storm-Shield PFI Installation Instructions Manual Download Page 27 | Manualshive

Page: 27 / 32

background image

TORSION BAR INSTALLATION:

Ensure that the ceiling fixing points are suitable to accept the weight of the torsion and spring

assembly.

Fix the flat spring anchor brackets to the free ends of the horizontal tracks, Figure 61. Rest the assemble torsion bar on top of the
tracks, then slide one axle end into one bearing and then through the other bearing. Secure the centre bearing plate into a solid
foundation either directly or by the use of suitable steel angle.

Now secure the springs to the spring anchor bracket using 3/8” x 1½” hexagonal head bolts and 3/8” washers and nuts.

Unwind the lifting cable on both sides and thread the cable behind the wheel axles around the ring on the bottom hanger, through
between the pairs of corner brackets around the pulley wheel and over to the rear drums, Figure 61.

Attach the lifting cable to the cable drum by slipping the cable into the slot on the outside groove. (The ferrule will prevent the cable
from coming out). wind the cable by hand turning away from the door in an up and over direction. Once the cable is taut, slide the
cable drum against the end bearing bracket and tighten the 9.5 mm set-screws securely to the torsion bar. be careful not to over-
tighten the set-screws.

Refer to page 28 when adding spring tension.

FIGURE 60

FIGURE 61

NUT 1/4" FLANGED 0T2702

TOP BRACKET LH ASSEMBLY

WASHER

000785

NUT FLANGED

5/16"-UNC 45713

140 mm SHEAVE

PULLEY 0T5251

PLASTIC CURVE OT3170

BOLT SQ NECK

5/16"-UNCx7/8" 0T2714

NUT

3/8"-UNC

006553

BOLT 1/4"x1/2"-UNC 0T2709

SPACER 0T5252

TOP BRACKET LH ASSEMBLY

(parts may differ to those shown)

27

panelift

®

pFT, panelift

®

Icon

™

pFI, b&D Storm-Shield

™

pFI and Insul-Shield

™

Installation Instructions

Revision 9 - March 2016

«
...
25
26
27
28
29
...
»

Summary of Contents for Panelift B&D Storm-Shield PFI

































Reviews:

No comments

Related manuals for Panelift B&D Storm-Shield PFI

Brand: Gatekeeper Pages: 21

Brand: tau Pages: 4

Brand: V2 Pages: 22

Brand: Telcoma Automations Pages: 24

LiftMaster Professional 78LM

Brand: Chamberlain Pages: 2

Brand: Nice Pages: 148

Smart Garage MYQ-G0401

Brand: Chamberlain Pages: 4

Brand: Black & Decker Pages: 8

Gizmo EM200 Series

Brand: Black & Decker Pages: 2

SeceuroGlide Compact

Brand: SWS Pages: 12

Brand: FAAC Pages: 22

Brand: Xtreme Garage Pages: 28

Brand: Ghost Controls Pages: 68

WING 302 Series

Brand: Dea Pages: 32

Brand: Dea Pages: 44

Brand: CAB Pages: 13

Brand: Rollerdor Pages: 20

76501 - Cordless Can Opener

Brand: Hamilton Beach Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands