7 / 28
0006160025_201305
ENGLISH
TECHNICAL FUNCTIONAL CHARACTERISTICS
• Gas burner compliant with European standard EN676.
• Operation with two progressive power stages.
• Combustion head with partial recirculation of combusted gases
with reduced NOx emissions (class II in European standard
EN676).
• Hinge opens both ways to permit convenient access to the mixer
without dismantling the burner from the boiler.
• Minimum and maximum air flow adjustment for first and second
stage by means of modulator with mechanical cam activated
by an electric servomotor.
• Gate closing in pause to prevent any heat dispersion to the flue.
• Valve seal control according to European Standard EN 676.
BURNER CONNECTION TO THE BOILER
ASSEMBLING THE HEAD UNIT
The combustion head is packaged separately from the body of
the burner.
Anchor the head unit to the boiler door as follows:
• Position the insulating seals on the lung (B).
• Anchor the flange of the lung (A) to the boiler (C) with the stud
bolts, washers and nuts provided (D), moving the lung with
the eye bolts.
Completely seal the gap between the burner sleeve and
the hole in the refractory material inside the boiler door with
suitable material.
ASSEMBLY THE VENTILATING BODY
The burner hinge can be opened both ways, it is therefore possible
to choose the opening side of the ventilating body. The burner is
manufactured for hinge installation on the right side. To enable the
maximum opening and so facilitate maintenance operations, it is
recommended to install the hinge on the
side of the burner opposite to the position
where the gas train is installed.
For a correct installation of the ventilating
body, follow the procedure described
below:
• After installing the head unit on the
boiler, assemble the two hinges (E)
on the lung using the 4 screws (F) and
the corresponding washers, without
tightening the screws completely
(hinges are pre-assembled on the
right side, but it is possible to mount
them on the opposite side).
• Place the ventilating body (G)
corresponding to the two hinges
(FIG 2). To handle the ventilating
body, use the specific chains or
ropes anchored to the eyebolts (H).
• Insert pin I, then lock it using the nuts
L and the corresponding washers,
taking care that the abutting surfaces
FIG.1
FIG.2
Summary of Contents for TBG 1100 MC
