background image

H0665600 

REV 

A

OPERATION AND 

MAINTENANCE MANUAL

 WARNING

IF THESE INSTRUCTIONS ARE NOT FOLLOWED 

EXACTLY, A FIRE OR EXPLOSION MAY RESULT, 

CAUSING PROPERTY DAMAGE, PERSONAL 

INJURY, OR DEATH.

FOR YOUR SAFETY: 

This product must be installed and serviced by a contractor who is licensed and qualified in pool equipment 

by the jurisdiction in which the product will be installed where such state or local requirements exists. In the event no such state or 
local requirement exists, the installer or maintainer must be a professional with sufficient experience in pool equipment installation 
and maintenance so that all of the instructions in this manual can be followed exactly. Before installing this product, read and follow all 
warning notices and instructions that accompany this product. Failure to follow warning notices and instructions may result in property 
damage, personal injury, or death. Improper installation and/or operation can create carbon monoxide gas and flue gases which can 
cause serious injury, property damage, or death. For installations in the vicinity of occupied/living spaces, as an additional measure 
of safety, Zodiac Pool Systems LLC strongly recommends installation of suitable carbon monoxide detectors in the vicinity of this 
appliance and in any adjacent occupied spaces. Improper installation and/or operation may void the warranty.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
  •  Immediately switch off main gas supply.
  •  Do not try to light any appliance.
  •  Do not touch any electrical switch; do not use any phone in your building.
  •  Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
  •  If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Grand Effects

®

Fire Bowls and Inserts Premium Line

Automated Operation

Summary of Contents for 100

























Reviews: