Balluff BIP LD2-T017-01-EP-S4 Series, User Manual

Page: 49 / 212

6.8 Switching Signal Channels, SSC
With the BIP sensor you can program four independent
switching states (Switching Signal Channels, SSCs).
Each switching signal is configured using profile-specific
parameters (see Tab. 6-10). Configuring the switching
channel begins by setting the channel using Index 0x003A.
Index Parameters Subindex Parame-
ters
Data format Access Data
0x003A Teach-In Channel
Setting
0x00 UINT8 R/W 0x01: SSC1
0x02: SSC2
0x03: SSC3
0x04: SSC4
0x003B Teach-In Status 0x00 UINT8 R
0x003C Set Point value
(SSC1)
0x01 Setpoint1 INT16 R/W –32000…+32000
0x02 Setpoint2 INT16 R/W –32000…+32000
0x003D Switching Signal
configuration SSC1
0x01 logic UINT8 R/W 0x00 : normal mode
0x01: inverted mode
0x02 mode UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
0x03 hysteresis INT16 R/W 50…16900 μm
0x003E Set Point value
(SSC2)
0x01 Setpoint1 INT16 R/W –32000…+32000
0x02 Setpoint2 INT16 R/W –32000…+32000
0x003F Switching Signal
configuration SSC2
0x01 logic UINT8 R/W 0x00 : normal mode
0x01: inverted mode
0x02 mode UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
0x03 hysteresis INT16 R/W 50…16900 μm
0x4000 Set Point value
(SSC3)
0x01 Setpoint1 INT16 R/W –32000…+32000
0x02 Setpoint2 INT16 R/W –32000…+32000
0x4001 Switching Signal
configuration SSC3
0x01 logic UINT8 R/W 0x00 : normal mode
0x01: inverted mode
0x02 mode UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
0x03 hysteresis INT16 R/W 50…16900 μm
0x4002 Set Point value
(SSC4)
0x01 Setpoint1 INT16 R/W –32000…+32000
0x02 Setpoint2 INT16 R/W –32000…+32000
0x4003 Switching Signal
configuration SSC4
0x01 logic UINT8 R/W 0x00 : normal mode
0x01: inverted mode
0x02 mode UINT8 R/W 0x01: Single point
0x02: Window mode
0x03 Two Point mode
0x03 hysteresis INT16 R/W 50…16900 μm
Tab. 6-10: Profile-specific parameters
6
IO-Link interface (continued)
Based on the Smart Sensor profile the Parameter
Switching Signal configuration can be used to set the
behavior of the switching points:
– Single-point mode, (Fig. 6-2): Value: 1
– Two-point mode, (Fig. 6-3): Value: 3
– Windowed mode, (Fig. 6-4): Value: 2
Switching signals can only be taught as long as
the position value is valid.
www.balluff.com 17 english
BIP LD2-T017-01-EP _ _ / EP _ _ -S4
Inductive Positioning System