1.9 Entering global data
The global menu is used to enter information that is not
specific to either of the individual channels. Information
programmed via this menu is used to compute parameters
such as the sum, difference or average of the channel 1
and channel 2 signals (for a 2-channel meter). In addition,
several general system parameters may be entered in the
global menu.
IMPORTANT
When calculating the sum, difference or average
readouts, data from the global-system submenu is used.
Any conflicting data entered in the channelx-system
submenu is overridden.
The following submenus are included in the global menu:
•
Systm
- use to specify the units of measure used in
calculations (see
Entering global system data on
).
•
I/O
- used to set up error handling and to configure
analog inputs and outputs (see
•
Comm
- used to set up the serial communications
port (see
Configuring the communications port on
).
Based on the selection made above, proceed to the
appropriate section of this chapter for instructions. While
following the programming instructions, refer to
. Remember to record all programmed data in
Appendix B. Data records on page 45
.
1.9.1 Entering global system data
This menu enables you to select the system units that
the XGF868i will use when channel data is added,
subtracted or averaged together.
1. In the
keypad program
, scroll to
prog
and
press [enter].
2. In the
prog
menu, scroll to GLOBL and
press [enter].
3. In the global
program
menu, scroll to
systm
and
press [enter].
4. At the
system units
prompt, scroll to
Eng
to display
measurements in English units or to
metrc
for
metric units and press [enter].
5. Scroll to the desired
pressure units
(absolute
or gauge) and press [enter].
6. Do one of the following:
• If absolute was selected, proceed immediately
to step 7.
• If gauge was selected, enter the desired
atmospheric pressure
, press [enter] and proceed
to the next step.
1.9.1a Selecting volumetric units
1. Scroll to the desired
volumetric units
for the flow rate
display and press [enter]. Available units are listed in
Table 5
below.
Table 5: Available volumetric/totalizer units
English
metric
ACF = Actual cubic feet
ACM = Actual cubic meters
KACF = Thousands of ACF
KACM = Thousands of ACM
MMACF = Millions of ACF
MMACM = Millions of ACM
SCF = Standard cubic feet SCM = Standard cubic meters
KSCF = Thousands of SCF
KSCM = Thousands of SCM
MMSCF = Millions of SCF
MMSCM = Millions of SCM
2. Scroll to the desired
time
units for the flow rate display
and press [enter].
3. Scroll to the desired number of
vol decimal digits
(digits to the right of the decimal point in the volumetric
flow rate display) and press [enter].
1.9.1b Selecting totalizer units
1. Scroll to the desired
totalizer units
for the totalized flow
rate display and press [enter]. Available units are listed in
2. Scroll to the desired number of
tot decimal digits
(digits to the right of the decimal point in the totalized
flow rate display) and press [enter].
3. Do one of the following:
• If
mass flow
is
on
, proceed to
selecting the mass flow
units
below.
• If
mass flow
is
off
, the meter returns to the channel
program
window. Go to
procedure options
on the
following page.
NOTE:
To activate mass flow, refer to
. The following prompts will only appear if mass
flow is activated for both channels.
12
Summary of Contents for DigitalFlow XGF868i
