manualshive.com logo in svg

Bailey Infi 90 IMFBS01, Instruction

The Bailey Infi 90 IMFBS01 user manual is your go-to instruction guide for maximizing the potential of this exceptional product. Easily download the comprehensive manual for free from our website, and unleash the full capabilities of the Bailey Infi 90 IMFBS01 at your fingertips.

Share
Download
background image

Index - 2

  

I-E96-302B

Index

 (continued)

®

N

NIAI04

Cable connections................................................ B-2
Configuration ........................................................ B-1
Dipswitch settings................................................. B-2
Input circuit ........................................................... B-1
Installation .............................................................3-5
Terminal assignments .......................................... B-1

Nomenclature..............................................................1-6
NTAI05

Cable connections................................................ A-2
Configuration ........................................................ A-1
Dipshunt settings.................................................. A-2
Installation .............................................................3-5
Terminal assignments .......................................... A-3

NTFB01.......................................................................5-2

Cable connections................................................ C-2
Configuration ........................................................ C-1
Input circuit ........................................................... C-1
Terminal assignments .......................................... C-2

O

Operating mode jumper (J1) .......................................3-4
Operating procedures .................................................5-1
Operation, system .......................................................2-1
Ordering parts .............................................................9-1

P

P1 edge connector pin assignments ...........................6-3
P2 edge connector pin assignments ...........................6-4
P3 input signal pin assignments..................................6-4
P4 pin assignments.....................................................6-4
Pin assignments, edge connector ...............................6-3
Point-to-point operation.............................................. A-1
Preventive maintenance schedule ..............................7-1
Printed circuit board cleaning......................................7-3
Procedures, maintenance ...........................................7-2

R

R22 adjustment .......................................................... 4-1
Red/green LED........................................................... 5-3
Reference documents ................................................ 1-6
Repair and replacement procedures .......................... 8-1
Replacement parts ..................................................... 9-1
Replacing a module .................................................... 8-1

S

Smart transmitter error codes ..................................... 6-2
Special handling ......................................................... 3-1
Specifications ............................................................. 1-7
Start-up....................................................................... 5-1
Status LED ................................................................. 5-3
Status reports ............................................................. 6-1
STT02 smart transmitter terminal ............................... 5-2
Support services ......................................................... 9-1
Switch settings............................................................ 3-3
System operation........................................................ 2-1

T

Technical documentation............................................ 9-1
Termination module

Configuration ........................................................B-1
Installation............................................................. 3-5

Termination unit

Configuration ........................................................A-1

FBS .................................................................C-1

Installation............................................................. 3-5

Terms and abbreviations ............................................ 1-5
Tools required for maintenance .................................. 7-2
Training....................................................................... 9-1
Transmitter, error codes ............................................. 6-2
Troubleshooting .......................................................... 6-1

U

Unpacking................................................................... 3-2

Summary of Contents for Infi 90 IMFBS01


























































Reviews:

No comments

Related manuals for Infi 90 IMFBS01

A10 Harmony Controller 2000 Installation Manual preview
Harmony Controller 2000
Brand: A10 Pages: 27
Raypak RayTemp Installation & Operating Instructions Manual preview
RayTemp
Brand: Raypak Pages: 24
J+J S 20 Handbook preview
S 20
Brand: J+J Pages: 91
Watts FEBCO 860 Small Series Installation Maintenance Repair Manual preview
FEBCO 860 Small Series
Brand: Watts Pages: 12
Bardiani Valvole BBZS5 Instruction, Use And Maintenance Manual preview
BBZS5
Brand: Bardiani Valvole Pages: 54
Parker 890CS Product Manual preview
890CS
Brand: Parker Pages: 478
SOMFY Situo 1 RTS Installation And Operating Manual preview
Situo 1 RTS
Brand: SOMFY Pages: 112
Magicfx FX-COMM4NDER MFX3203 User And Installation Manual preview
FX-COMM4NDER MFX3203
Brand: Magicfx Pages: 16
Hattersley C31 Installation And Operating Instructions preview
C31
Brand: Hattersley Pages: 2
National Instruments PXIe-6595 Getting Started Manual preview
PXIe-6595
Brand: National Instruments Pages: 6
schmersal AES 1175 Operating Instructions Manual preview
AES 1175
Brand: schmersal Pages: 6
YASKAWA MP2600iec Hardware Manual preview
MP2600iec
Brand: YASKAWA Pages: 42
YASKAWA MP210 Series User Manual preview
MP210 Series
Brand: YASKAWA Pages: 351
Gardena 1891-20 Operator'S Manual preview
1891-20
Brand: Gardena Pages: 15
Samson 2371-10 Mounting And Operating Instructions preview
2371-10
Brand: Samson Pages: 36
Quick THRUSTER COMMAND TCD 1022 E Manual For Use And Installation preview
THRUSTER COMMAND TCD 1022 E
Brand: Quick Pages: 56
Senect AQUACULTURE AQC-A1-333-150 Manual preview
AQUACULTURE AQC-A1-333-150
Brand: Senect Pages: 49
NCD ZigBee ZSCAN16 MIRROR Manual preview
ZigBee ZSCAN16 MIRROR
Brand: NCD Pages: 12

Brands by name

Popular brands

Load more brands