manualshive.com logo in svg

Bailey Infi 90 IMFBS01, Instruction

Share
Download
Bailey Infi 90 IMFBS01 Instruction Download Page 5

vi

  

I-E96-302B

Safety Summary

®

Sommaire de Sécurité

GENERAL

 WARNINGS

Equipment Environment
All components, whether in transportation, operation or storage,
must be in a noncorrosive environment.

Electrical Shock Hazard During Maintenance
Disconnect power or take precautions to insure that contact with
energized parts is avoided when servicing.

SPECIFIC

WARNINGS

Disconnect power before installing dipshunts on the module mount-
ing unit backplane. Failure to do so will result in contact with cabinet
areas that could cause severe or fatal shock. (p. 3-5)

Wear eye protection whenever working with cleaning solvents.
When removing solvents from printed circuit boards using com-
pressed air, injury to the eyes could result from splashing solvent as
it is removed from the printed circuit board. (p. 7-1)

AVERTISSEMENTS

D’ORDRE

GÉNÉRAL

Environnement de l’équipement
Ne pas soumettre les composants à une atmosphère corrosive lors
du transport, de l’entreposage ou l’utilisation.

Possibilité de chocs électriques durant l’entretien
Débrancher l’alimentation ou prendre les précautions pour éviter
tout contact avec des composants sous tension durant l’entretien.

AVERTISSEMENTS

D’ORDRE

SPÉCIFIQUE

Interrompez l'alimentation avant d'installer des dipshunts sur le fond
de panier du châssis de montage des modules. Sinon, tout contact
avec cette zone entraîne des risques d'électrocution sérieuse ou
fatale. (p. 3-5)

Des lunettes de protection devraient être portées lors de travail
avec des solvants nettoyants. Lorsqu'on enlève les solvants des cir-
cuits imprimés à l'aide d'air comprimé, les éclaboussures de solvant
pourraient causer des blessures aux yeux. (p. 7-1)

Summary of Contents for Infi 90 IMFBS01


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands