Bailey Infi 90 IMFBS01 Instruction Download Page 44 | Manualshive

Page: 44 / 57

background image

MAINTENANCE

PREVENTIVE MAINTENANCE PROCEDURES

I-E96-302B

7 - 3

Printed Circuit Board Cleaning

There are several circuit board cleaning procedures in this sec-
tion. These procedures cover circuit board cleaning and wash-
ing, cleaning edge connectors and circuit board laminate
between edge connectors. Use the procedures that meet the
needs of each circuit board. Remove all dust, dirt, oil, corrosion
or any other contaminant from the circuit board.

Do all cleaning and handling of the printed circuit boards at
static safe work stations. Always observe the steps listed under

SPECIAL HANDLING

in Section 3 when handling printed cir-

cuit boards.

GENERAL CLEANING AND WASHING

If the printed circuit board needs minor cleaning, remove dust
and residue from the printed circuit board surface using clean,
dry, filtered compressed air or an antistatic field service vac-
uum cleaner.

Another method of washing the printed circuit board is:

1. Clean the printed circuit board by spraying it with isopro-
pyl alcohol (99.5% electronic grade) or wiping the board with a
foam tipped swab wetted in isopropyl alcohol.

2. When the circuit board is clean, remove excess solvent by
using compressed air to blow it free of the circuit board.

EDGE CONNECTOR CLEANING

To clean edge connector contacts:

1. Use a solvent mixture of 80% isopropyl alcohol (99.5% elec-
tronic grade) and 20% distilled water.

2. Soak a lint free cloth with the solvent mixture.

3. Work the cloth back and forth parallel to the edge connec-
tor contacts.

4. Repeat with a clean cloth that is soaked with the solvent
mixture.

5. Dry the edge connector contact area by wiping with a clean
lint free cloth.

«
...
42
43
44
45
46
...
»

Summary of Contents for Infi 90 IMFBS01


























































Reviews:

No comments

Related manuals for Infi 90 IMFBS01

Brand: Balboa Instruments Pages: 10

Brand: Quantum Data Pages: 36

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 98

Brand: NAiS Pages: 173

Brand: Panasonic Pages: 2

Brand: Calsense Pages: 74

Brand: CALEFFI Pages: 12

QuickSetter+ 132 Series

Brand: CALEFFI Pages: 5

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: Maestra Pages: 22

Brand: Lamtec Pages: 136

Brand: Vacon Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands