manualshive.com logo in svg

Bailey Infi 90 IMFBS01, Instruction

Share
Download
Bailey Infi 90 IMFBS01 Instruction Download Page 39

TROUBLESHOOTING

ERROR MESSAGES AND CORRECTIVE ACTION

6 - 2

  

I-E96-302B

®

A communication failure will occur if a configuration download
is attempted to a transmitter whose configuration lockout
jumper is set to the lockout position. Each smart transmitter
has its own function block. If a smart transmitter communica-
tion failure occurs, its function block appears in the 

I/O SLAVE

report listing. 

NOTE:  The configuration lockout jumper (on the transmitter) pre-
vents the transmitter from being configured. Transmitter configura-
tion and operation can be monitored, but the transmitter
configuration cannot be changed from any source. Refer to the
smart transmitter product instruction for information about using the
lockout feature. 

Missing I/O Module Error

A missing I/O module error (no FBS response or wrong type)
occurs when the FBS address (set by dipswitch S1 on the FBS
module) does not match the I/O module address in the control

Table 6-1.  IMFBS01 Error Codes

Error

 No.

Description

Corrective Action

1

No FBS module 
response or wrong 
module type

Check FBS jumper and switch settings. 
Replace the IMFBS01 if jumper and switch 
settings check good.

Check function code 132 for correct specifica-
tion values, such as I/O module address.

2

Calibration error

Check the FBS input calibration.

3

Channel failure or 
out of range

Check TU or TM and cabling. Replace 
IMFBS01 if cabling is good.

Check function code 132 for correct specifica-
tion values, such as I/O module address.

NOTE: Out of range refers to values of FBS analog inputs.

Table 6-2.  Smart Transmitter Error Codes

Error No.

Description

6

Not responding

7

Configuration mismatch

8

Wrong transmitter type

9

Input failure or memory failure

10

Overpressured

11

Temperature range exceeded

12

Output fixed

13

Calibration required

14

Transmitter being calibrated

15

Transmitter off-line

16

Communication error

Summary of Contents for Infi 90 IMFBS01


























































Reviews:

No comments

Brands by name

Popular brands

Load more brands