manualshive.com logo in svg

Bailey Infi 90 IMFBS01, Instruction

The Bailey Infi 90 IMFBS01 user manual is your go-to instruction guide for maximizing the potential of this exceptional product. Easily download the comprehensive manual for free from our website, and unleash the full capabilities of the Bailey Infi 90 IMFBS01 at your fingertips.

Share
Download
background image

I-E96-302B   

Index 

- 

1

Index

A

Address selection switch (S1) .................................... 3-3
Adjustment, R22 ......................................................... 4-1

B

Blinking green status LED .......................................... 6-3

C

Calibration

Adjusting R22 ....................................................... 4-1
Field bus module .................................................. 4-1
Required equipment ............................................. 4-1

Checking connections ................................................ 7-2
Circuit board cleaning................................................. 7-3
Cleaning printed circuit boards ................................... 7-3
Communication levels ................................................ 1-2
Communication mode jumper (J2, J3)........................ 3-4
Connector pin assignments, edge .............................. 6-3

D

Digital inputs, FSK (field bus mode) ........................... 2-8
Dipswitch settings....................................................... 3-2
Documentation ........................................................... 9-1

E

Edge connector pin assignments ............................... 6-3
Error

Codes, smart transmitter ...................................... 6-2
Configuration mismatch ........................................ 5-1
Corrective actions ................................................. 6-1
I/O module missing ............................................... 6-2
Messages ............................................................. 6-1
Transmitter not responding................................... 5-1

F

Factory test jumper (J4).............................................. 3-4
Firmware requirements............................................... 3-2
FSK digital inputs (field bus mode)............................. 2-8
Function codes 132 and 133 ...................................... 3-2

G

Glossary ..................................................................... 1-5

H

Handling ..................................................................... 3-1
Hazardous location installation................................... 3-2

I

Inspection.................................................................... 3-2
Installation

Field bus module ................................................... 3-5
Hazardous locations.............................................. 3-2
Termination module .............................................. 3-5
Termination unit .................................................... 3-5

Instruction ................................................................... 1-5

Contents ................................................................ 1-4
Glossary ................................................................ 1-5
Intended user ........................................................ 1-1
Nomenclature ........................................................ 1-6
Overview ............................................................... 1-1
Reference documents ........................................... 1-6
Using ..................................................................... 1-4

J

Jumper settings

J1 .......................................................................... 3-4
J2-J3 ..................................................................... 3-4
J4 .......................................................................... 3-4

L

LED

Blinking green ................................................5-3, 6-3
Green .................................................................... 5-3
Red........................................................................ 5-3
Status .................................................................... 5-3

M

Maintenance

Equipment required ............................................... 7-2
Overview ............................................................... 7-1
Schedule ............................................................... 7-1

Missing I/O module, error............................................ 6-2
Module

Application............................................................. 1-2
Communication levels ........................................... 1-2
Description .....................................................1-1, 2-1
Error codes............................................................ 6-2
Features ................................................................ 1-3
Operation .............................................................. 2-1
Repair.................................................................... 8-1
Replacement ......................................................... 8-1
Specifications ........................................................ 1-7
Status reports ........................................................ 6-1
System operation .................................................. 2-1

Summary of Contents for Infi 90 IMFBS01


























































Reviews:

No comments

Related manuals for Infi 90 IMFBS01

Waterway OASIS Instruction Manual preview
OASIS
Brand: Waterway Pages: 16
Oldham MX15 Installation And Operating Manual preview
MX15
Brand: Oldham Pages: 32
H3C PSR3000-54A Manual preview
PSR3000-54A
Brand: H3C Pages: 14
VAT 150 Series Installation, Operating, & Maintenance Instructions preview
150 Series
Brand: VAT Pages: 27
ICP DAS USA ET-7000 series User Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 148
ICMA S001 Technical Information Sheet preview
S001
Brand: ICMA Pages: 8
jablotron Oasis JA-80 Installation Manual preview
Oasis JA-80
Brand: jablotron Pages: 22
jablotron JA-113E Manual preview
JA-113E
Brand: jablotron Pages: 2
Lawler 804 Installation & Maintenance Manual preview
804
Brand: Lawler Pages: 5
Rain Bird ESP-LXD Installation, Programming & Operation Manual preview
ESP-LXD
Brand: Rain Bird Pages: 138
K&K M3500N Installation Instructions Manual preview
M3500N
Brand: K&K Pages: 10
praher SUPERSTAR E-3000/F2 Operating Instructions Manual preview
SUPERSTAR E-3000/F2
Brand: praher Pages: 10
IDEC HR6S-S Original Instructions Manual preview
HR6S-S
Brand: IDEC Pages: 97
Nordelettronica NE274 Instruction Manual preview
NE274
Brand: Nordelettronica Pages: 8
Qcells Q.PEAK DUO XL-G11S.X / BFG Series Installation And Operation Manual preview
Q.PEAK DUO XL-G11S.X / BFG Series
Brand: Qcells Pages: 26
EpiSensor ZDR-10 User Manual preview
ZDR-10
Brand: EpiSensor Pages: 37
Potter PFC-4064 Keypad Programming Manual preview
PFC-4064
Brand: Potter Pages: 25
Pangolin FB4 Series User Manual preview
FB4 Series
Brand: Pangolin Pages: 35

Brands by name

Popular brands

Load more brands