Bailey Infi 90 IMFBS01 Instruction Download Page 14

Page: 14 / 57

INTRODUCTION

REFERENCE DOCUMENTS

1 - 6

I-E96-302B

REFERENCE DOCUMENTS

Table

1-2

lists Elsag Bailey instructions referenced in this

instruction.

NOMENCLATURE

Table

1-3

contains the nomenclature used in this instruction.

The modules, equipment and software packages listed can be
used with an FBS module.

Table 1-2. Reference Documents

Number

Title

C-E96-110

Operator Interface Station

C-E96-800

Engineering Workstation

I-E21-28

Smart Transmitter Terminal, Type STT02

I-E21-28-1

Smart Transmitter Terminal, Type STT02E

I-E92-501-2

Configuration and Tuning Terminal, Type CTT02

I-E93-714

Personal Computer Software Smartport (SEEK)

I-E96-200

Function Code Application Manual

I-E96-201

IMMFP01 Multi-Function Processor

I-E96-202

IMMFP02 Multi-Function Processor

I-E96-211

IMMFC03 Multi-Function Controller

I-E96-212

IMMFC04 Multi-Function Controller

I-E96-213

IMMFC05 Multi-Function Controller

I-E96-416

NTAI05 Analog Input Termination Unit

I-E96-432

NTFB01 Field Bus Slave Termination Unit

I-E96-436

NIAI04 Analog Input Termination Module

P-E21-001

Installing a 4 to 20 mA Transmitter in a Hazardous Location

Table 1-3. Nomenclature

Nomenclature

Hardware

BC, BCN

Smart pressure transmitters

EQ, EQN

Smart temperature transmitters

MFC

Multi-function controller module

MFP

Multi-function processor module

NIAI04

Analog inputs termination module

NTAI05

Analog inputs termination unit

NKTM01, NKTU02

Analog inputs termination module cable

NKTU01

Analog inputs/field bus termination unit cable

NTFB01

Field bus termination unit

PTS

Smart pressure transmitters

SEEK0

Smartport software

STT02E

Smart transmitter terminal

TBN

Smart pH transmitters

Summary of Contents for Infi 90 IMFBS01


























































Search results

Summary of Contents for Infi 90 IMFBS01

Reviews:

Brands by name

Popular brands

Bailey Infi 90 IMFBS01, Instruction

Search results

Summary of Contents for Infi 90 IMFBS01

Reviews:

Brands by name

Popular brands