Bailey Infi 90 IMFBS01 Instruction Download Page 15

Page: 15 / 57

INTRODUCTION

SPECIFICATIONS

I-E96-302B

1 - 7

SPECIFICATIONS

Table

1-4

contains the specifications for the IMFBS01 module.

Table 1-4. Specifications

Property

Characteristic/Value

Power requirements

Operating power

5 VDC, ±5% at 85 mA typical
+15 VDC, ±5% at 25 mA typical
-15 VDC, ±5% at 20 mA typical

Power dissipation

1.1 W typical

Installation category

III for power per ANSI/ISA S:2.01-1994

Operating

Analog inputs

15 independently configured channels

Analog input ranges

4 to 20 mA, 1 to 5 VDC, 0 to 1 VDC,
0 to 5 VDC, 0 to 10 VDC, -10 to +10 VDC

Analog updates

A/D conversions 5 times/sec

FSK digital updates

3 to 10 times/sec (in field bus configuration)

A/D resolution

14 bits with polarity

Analog accuracy

4 to 20 mA 0.1%
1 to 5 VDC 0.1%
0 to 5 VDC 0.1%
0 to 10 VDC 0.1%
±10 VDC 0.1%
0 to 1 VDC 0.25%

Common mode voltage

-12 VDC minimum, +15 VDC maximum
±12 VDC (±1 VDC) input span
±10 VDC (±5 VDC) input span
±5 VDC (±10 VDC) input span

Common mode rejection

90 dB minimum at 60 Hz

Normal mode rejection

70 dB minimum at 60 Hz

Input impedance

Greater than 1 M

Ω

(every channel)

Installation category

III for inputs per ANSI/ISA S:2.01-1994

Environmental

Electromagnetic/radio
frequency interference

No values available at this time. Keep cabinet doors closed. Do not use
communication equipment closer than 2 m (6 ft) from the cabinet.

Ambient temperature

0° to 70°C (0° to 158°F) (noncondensing)

Relative humidity

5% to 95% up to 55°C (131°F)
5% to 45% at 70°C (158°F) (noncondensing)

Atmospheric pressure

Sea level to 3 km (1.86 mi)

Air quality

Noncorrosive

Mounting

Occupies a single slot in a standard INFI 90 module mounting unit (MMU)

Certification

Canadian Standards
Association (CSA)

Certified for use as process control equipment in an ordinary
(nonhazardous) location

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

Summary of Contents for Infi 90 IMFBS01


























































Search results

Summary of Contents for Infi 90 IMFBS01

Reviews:

Brands by name

Popular brands

Bailey Infi 90 IMFBS01, Instruction

Search results

Summary of Contents for Infi 90 IMFBS01

Reviews:

Brands by name

Popular brands