Axminster Trade AT254SB Original Instructions Manual Download Page 7

Page: 7 / 52

General Instructions for 230V Machines

The following will enable you to observe good working
practices, keep yourself and fellow workers safe and
maintain your tools and equipment in good working
order.

WARNING!! KEEP TOOLS AND EQUIPMENT
OUT OF REACH OF YOUNG CHILDREN

Mains Powered Tools
• Tools are supplied with an attached 13 Amp plug.
• Inspect the cable and plug to ensuree that neither

are damaged. Repair if necessary by a suitably
qualified person.

• Do not use when or where it is liable to get wet.

Workplace
• Do not use 230V a.c. powered tools anywhere within

a site area that is flooded.

• Keep machine clean.
• Leave machine unplugged until work is about to

commence.

• Always disconnect by pulling on the plug body and

not the cable.

• Carry out a final check e.g. check the cutting tool

is securely tightened in the machine and the correct
speed and function set.

• Ensure you are comfortable before you start work,

balanced, not reaching etc.

• Wear appropriate safety clothing, goggles, gloves,

masks etc. Wear ear defenders at all times

• If you have long hair wear a hair net or helmet to

prevent it being caught up in the rotating parts of
the machine.

• Consideration should be given to the removal of

rings and wristwatches.

• Consideration should also be given to non-slip

footwear etc.

• If another person is to use the machine, ensure they

are suitably qualified to use it.

• Do not use the machine if you are tired or distracted
• Do not use this machine within the designated safety

areas of flammable liquid stores or in areas where
there may be volatile gases.

• Check cutters are correct type and size, are undam-

aged and are kept clean and sharp, this will maintain
their operating performance and lessen the loading
on the machine.

• OBSERVE…. make sure you know what is happening

around you and USE YOUR COMMON SENSE.

KEEP WORK AREA AS UNCLUTTERED AS IS
PRACTICAL. UNDER NO CIRCUMSTANCES SHOULD
CHILDREN BE ALLOWED IN WORK AREAS.

Summary of Contents for AT254SB





















































Search results

Summary of Contents for AT254SB

Reviews:

Related manuals for AT254SB

Brands by name

Popular brands

Axminster Trade AT254SB, Original Instructions Manual

Search results

Summary of Contents for AT254SB

Reviews:

Related manuals for AT254SB

Brands by name

Popular brands