Axminster Trade AT254SB Original Instructions Manual Download Page 9 | Manualshive

Page: 9 / 52

background image

Initial Assembly

09

PLEASE RECYCLE ANY UNWANTED PACKAGING RESPONSIBLY

Saw Body Assembly

Having unpacked the boxes, put the parts and
components where they are readily to hand. Break
down the main box by knocking the sides away (be
careful of exposed nails etc.), but leave the machine
sitting on its pallet. Identify the short rear panel
with the dust extraction cutout (2), locate the dust
extraction moulding (4) and fit to the panel using
the nuts and bolts (5) provided. (See fig 1)

The orientation of the moulding should leave the
30mm outlet pointing upwards i.e. pointing up the
long length of the panel. Put the panel aside, and
locate the lower leg columns (3) and 4 No. M8x16mm
(5A) bolts, nuts and double washers. Fix the lower legs
to the upper legs using a washered bolt through the
legs and secure with washer and nut, only turn the nuts

up finger tight at this time. (See fig 2) Locate the rear
extention table (6), table support brackets (7) and 4 No.
M8 x20mm caphead bolts and washers (9).

NOTE: the manufacturer has fitted adjusting bolts
to the brackets, these are the faces that back
against the legs.

NOTE: The upper leg columns (3) has welded nuts
to the inside face to mount the support brackets (7)

Fasten the support brackets (7) to the upper leg
columns (3) using the bolts washers (9) and finger
tighten the at this time. (See fig 4-5-6)

Fig 1

Fig 2

2

3

4

5

Fig 3

Fig 4

7

5A

«
...
7
8
9
10
11
...
»

Summary of Contents for AT254SB





















































Reviews:

No comments

Related manuals for AT254SB

Brand: Total Pages: 13

Brand: Ryobi Pages: 14

Brand: King Industrial Pages: 12

Brand: IVT Pages: 120

Brand: Lumberjack Pages: 26

Brand: Tradesman Pages: 26

Brand: Parkside Performance Pages: 105

Brand: Jet Pages: 36

HP-11 PB DELUXE

Brand: H. Winter Pages: 32

Brand: Scheppach Pages: 164

Brand: Hitachi Pages: 68

Brand: Hitachi Pages: 17

Brand: Berner Pages: 172

Brand: Meec tools Pages: 49

Brand: GMC Pages: 62

Brand: Sparky Group Pages: 110

Brand: Wadkin Pages: 36

Brand: Kalamazoo Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands