Axminster Trade AT254SB Original Instructions Manual Download Page 35 | Manualshive

Page: 35 / 52

background image

Changing the Saw Blade

35

Raise the saw blade to it’s highest point. Remove the saw blade guard. Remove the 5 screws that secure
the table insert, place carefully aside and remove the table insert. (A) Using the spanner and the tommy bar
provided, put the spanner onto the flats on the nut. Turn the saw until the tommy bar hole (B) is visible.
Insert the tommy bar (18) and turn the saw to allow it to rest against the front edge of the saw slot. The
tommy bar hole is in the inside platewasher component. (See figs 110-111-112)

Fig 110

Fig 111

Fig 112

Fig 113

Slacken off the saw nut (remember left hand thread).
Remove the saw nut (C), then remove the sawplate
washer (D) and the saw blade. Now is a good time to
give the interior of the machine, the dust extraction
channels, etc. a thorough clean. (See figs 113-114)

Check the new blade for damage, missing
teeth,sharpness etc. Fit the new blade, ensure that
the teeth are pointing towards the front of the
machine. (See fig 115) Put the sawplate washer onto
the shaft and twist on the saw nut. Spin the nut up
finger tight and check the saw is correctly seated.

Fig 114

Fig 115

Teeth pointing

to the front

A

B

C

D

18

18A

WARNING! DISCONNECT THE
MACHINE FROM THE MAINS!

«
...
33
34
35
36
37
...
»

Summary of Contents for AT254SB





















































Reviews:

No comments

Related manuals for AT254SB

Brand: ICS Pages: 85

Brand: Ryobi Pages: 48

Brand: Jet Pages: 68

Brand: Erbauer Pages: 40

Brand: Wesco Pages: 32

Brand: Clarke Pages: 24

Brand: General International Pages: 23

Brand: Wadkin Bursgreen Pages: 27

Brand: Hyd-Mech Pages: 132

Brand: Scheppach Pages: 120

PPFD-2400 TYPE 1/1E

Brand: Echo Pages: 34

Brand: Dake Pages: 34

Brand: Worx Pages: 104

Brand: Scantool Pages: 26

Brand: Scantool Pages: 32

Brand: Scantool Pages: 32

Brand: Craftex Pages: 18

Brand: Craftex Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands