Axminster Trade AT254SB Original Instructions Manual Download Page 3

Page: 3 / 52

EU Declaration of Conformity

Cert No: MJ2325D / MJ2330D

Axminster Tools & Machinery Ltd
Axminster Devon
EX13 5PH UK
axminster.co.uk

Type

Saw Table

Model

AT234SB, AT315SB

and conforms to the machinery example for which the
EC Type-Examination Certificate No BM50300862
has been issued by Laizhou Fulin Machinery Co., Ltd.
at: Wenchang Road Street Nanwuli Industry Yard Laizhou, Shandong261400 China

and complies with the relevant essential health and safety requirements

2006/42/EC
06/42/EC - Annex I/05.2006
EN 1870-19:2013
EN 60204-1:2006+A1+AC

declares that the machinery described:-

This machine complies with the following directives:

EU Declaration of Conformity

EN 61000-3-3: 1995+A1
EN 55014-2: 1997+A1
EN 61000-3-2: 2000
EN 55014-1: 2000+A1

Signed

Andrew Parkhouse
Operations Director

Date: 07/01/2015

The symbols below advise the correct safety procedures when using this machine.

Fully read manual

and safety instructions

before use

Eye protection

should be worn

Ear protection

should be worn

HAZARD

Dust mask

should be worn

Summary of Contents for AT254SB





















































Search results

Summary of Contents for AT254SB

Reviews:

Related manuals for AT254SB

Brands by name

Popular brands

Axminster Trade AT254SB, Original Instructions Manual

Search results

Summary of Contents for AT254SB

Reviews:

Related manuals for AT254SB

Brands by name

Popular brands