manualshive.com logo in svg

Axis 26123R1, Integrator And User’S Manual, Page: 42 / 77

Share
Download
Axis 26123R1 Integrator And User’S Manual Download Page 42

 

42 

AXIS 282/AXIS 282A - Pan Tilt Zoom

Pan Tilt Zoom 

Installing PTZ Devices

The AXIS 282/AXIS 282A supports several PTZ devices. Please see www.axis.com for a 

complete list of supported devices, and to obtain the correct driver. Follow the instructions 

below to install a PTZ device:

1. Using an appropriate cable, connect the device to your selected port (RS-232 or 

RS-485). This configurable port is available via the 34 I/O pins. See pages 58 and 

59 for more information.

2. In the setup tools, go to 

Setup > System Options > Ports & Devices 

and then 

select the port (RS-232/RS-485) to configure. 

3. Select 

Pan Tilt Zoom

 from the 

Usage

 drop-down list.

4. Click 

Upload 

to install a PTZ driver

.

 

(PTZ drivers are available from the Axis Web site at www.axis.com)

5. Click 

Port Options...

 to modify the port settings. The default values correspond to 

the values specified by the PTZ driver.

6. From 

System Options > Ports & Devices

, select the port configured for PTZ and 

then select the video source to use with the device.

7. If required, click the Advanced Options button to make further settings and see 

the online help.

Summary of Contents for 26123R1














































































Reviews:

No comments