manualshive.com logo in svg

AVM T1, Manual, Page: 13 / 55

Share
Download
AVM T1 Manual Download Page 13

13

2 Hardware Installation

2 Hardware Installation

In order to maintain the full capabilities of the AVM
ISDN-Controller T1/T1-B, please observe the fol-
lowing precautions:

- The AVM ISDN-Controller T1/T1-B must not

be placed in humid areas.

- The ambient temperature should be between

15° and 35° C. The vents in the housing must
not be obstructed.

- The AVM ISDN-Controller T1/T1-B should be

placed on a firm, stable surface or mounted in a
19-inch equipment rack.

To install the AVM ISDN-Controller T1/T1-B, you
must have:

• An ISDN primary rate interface

• An ISDN NT (Network Terminator) including power

supply or separate power adapter, installed by your
ISDN provider

• A PC with a 486 or higher CPU and a free ISA or EISA

bus slot

Examine the contents of your AVM ISDN-Controller
T1/T1-B  package (see Chapter 1). If any part is
missing, contact your dealer immediately.

The hardware installation entails the following steps:

1. Installing the PC interface card

2. Connecting the cable from the PC interface card to

the AVM ISDN-Controller T1/T1-B

3. Connecting the cable from the T1 to the NT

4. Connecting the T1 power supply

These steps are described in order below. The illustra-
tions are found in Appendix B, Illustrations.

Summary of Contents for T1
























































Reviews:

No comments