Avitel 5303 Installation Manual Download Page 50

Page: 50 / 64

feature 2-10 for additional detail.

2-17 AUX 3 LINKING (NONE)/ARM, DISARM, REMOTE START: Refer to fea-

ture 2-13 for additional detail.

➤

Menu 3 - Remote start

3-1 Engine Checking Virtual Tach:

(1) When set to “virtual tach” (1) the remote

start monitors the cranking voltage of the vehicle and sets it as a reference point.

Fifteen seconds after the crank output sequence the remote start checks the volt-

age again to determine if the vehicle is running.

When set to voltage, (2) the unit cranks the starter for the programmed time and

then attempts to sense that the engine is running by detecting an increase in volt-

age. If programmed Off (3) the vehicle cranks for the programmed crank time.

The tach setting or voltage setting is not checked to verify that the car is running.

In the OFF setting, if the vehicle fails to start, the ignition stays on for the run dura-

tion. Using tach or either of the voltage settings is recommended.

When set to Tachometer, (4) the unit references the learned tach signal to disen-

gage the starter. In addition it will monitor the RPM and shut down if the engine

RPM is too high or too low.

3-2 RUN TIME

, 24, 60 MINUTES: Selects the time in minutes that the

system will operate the engine until the system "times out". This is the maximum

operation period and the system may be shut down using a shutdown at any

time. Using the Bitwriter®, the run time can be programmed for any duration

from 1-60 minutes.

3-3 Parking Lights

Constant:

In the default setting, the parking lights (if con-

nected)will come on solid during the remote start runtime. In the two- flash setting

the parking lights will flash during the remote start runtime. In the OFF setting, the

parking lights will not come ON or flash, when the vehicle is remote started.

Summary of Contents for 5303





























































Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands

Avitel 5303, Installation Manual

Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands