Avitel 5303 Installation Manual Download Page 19 | Manualshive

Page: 19 / 64

background image

19

© 2008 Directed Electronics. All rights reserved.

H1/11

WHITE

(+/-) SELECTABLE LIGHT FLASH OUTPUT

This wire is connected to the (+) parking light wire in the vehicle. If the light flash

polarity jumper under the sliding door is moved to the opposite position (See

Internal Programming Jumper section of this guide) this wire supplies a (-) 200

mA output.

(+) Positive Light Flash Output

(-) Negative Light Flash Output

WHITE H1/11

(+) LIGHT FLASH OUTPUT

WHITE H1/11

(-) LIGHT FLASH OUTPUT

Note:

For parking light circuits that draw 10-amps or more, the internal jumper

must be switched to a (-) light flash output. (See Setting the light flash polarity

section of this guide.) P/N 8617 or a standard automotive SPDT relay must be

used on the H1/11 light flash output harness wire.

H1/12

ORANGE

(-) 500mA GROUND WHEN ARMED OUTPUT

This wire supplies a (-)500 mA ground as long as the system is armed. The out-

put ceases as soon as the system is disarmed. The orange wire may be wired

to an optional Directed Electronics 8618 starter kill relay.

«
...
17
18
19
20
21
...
»

Summary of Contents for 5303

































































Reviews:

No comments

Related manuals for 5303

Brand: FCI Pages: 2

Brand: Magnavox Pages: 17

Brand: Xtralis Pages: 15

Brand: TFA Pages: 30

Brand: RHINO Pages: 6

Uniguard Superflow UG-5-AFR Series

Brand: CALECTRO Pages: 4

Brand: pyrexx Pages: 45

Brand: EURA Pages: 2

Brand: EST International Pages: 4

Brand: EST Pages: 4

Brand: CrimeStopper Pages: 4

CS-9200 Samurai

Brand: CrimeStopper Pages: 3

Brand: Vision Pages: 3

Brand: Ultra Start Pages: 12

Boomerang SF 6P150

Brand: SETRONIC VERONA Pages: 4

Boomerang S 6P150

Brand: SETRONIC VERONA Pages: 4

Brand: Gasmate Pages: 20

Brand: sparoom Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands