Avitel 5303 Installation Manual Download Page 30 | Manualshive

Page: 30 / 64

background image

30

© 2008 Directed Electronics. All rights reserved.

Shock sensor harness, 4-pin connector

H

GREEN

(-) MULTIPLEX INPUT, ZONE 2

Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while

inputs longer than 0.8 seconds will trigger full alarm sequence and report Zone

Two. If installing an optional Directed Electronics dual stage sensor, connect to

the green wire as shown below. The diagram below eliminates the need for

diodes to isolate the sensors.

Diagram for adding optional Directed Electronics dual stage sensor to green

wire (Zone 2):

H

BLUE

(-) MULTIPLEX INPUT, ZONE 2

Inputs shorter than 0.8 seconds will trigger the Warn Away® response, while

inputs longer than 0.8 seconds will trigger full alarm sequence and will also

report Zone Two.

H

RED/BLACK

RED: is (+) 12V CONSTANT, BLACK is (-) GROUND

Do not use these for anything besides the plug-in shock sensor.

«
...
28
29
30
31
32
...
»

Summary of Contents for 5303

































































Reviews:

No comments

Related manuals for 5303

Brand: Python Pages: 57

Brand: LEXIBOOK Pages: 9

Brand: FCI Pages: 47

Brand: AstroStart Pages: 20

Meridian WLS906-433

Brand: DSC Pages: 2

Brand: AV-GAD Pages: 2

Brand: Viper Pages: 44

Brand: Panther Pages: 20

Brand: Eurochron Pages: 8

Brand: System Sensor Pages: 4

Smoke Dampers SSSMDR-501

Brand: Greenheck Pages: 1

Smoke Dampers SMD-203

Brand: Greenheck Pages: 7

Brand: tibelec Pages: 92

car security system

Brand: PYLE Audio Pages: 10

Brand: Metasys Pages: 13

Brand: 2besmart Pages: 17

Brand: Cavius Pages: 15

Brand: Oregon Scientific Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands