Avitel 5303 Installation Manual Download Page 25 | Manualshive

Page: 25 / 64

background image

25

© 2008 Directed Electronics. All rights reserved.

➤

Remote start, (H3) secondary harness

H3/1

BLACK/WHITE

NEUTRAL SAFETY SWITCH INPUT

Connect this wire to the provided toggle (override) switch as shown in figure

A. Connect the other wire from the toggle switch to the park/neutral switch in

the vehicle. This wire will test with ground with the gear selector either in PARK

or NEUTRAL. This will prevent the vehicle from accidentally being started while

in a drive gear. This input MUST rest at ground in order for the remote start

system to operate. Connected properly the vehicle will only start while in PARK

or NEUTRAL.

In some vehicles, the park/neutral position switch activates a factory starter lock

out that will not allow the starter to operate in a drive gear. In these vehicles,

connect this wire to the toggle switch as shown in figure B. Connect the other

wire from the toggle switch to chassis ground.

Important

: Always perform the Safety Check section of this installation guide to

verify that the vehicle cannot be started in ANY drive gear and that the override

switch is functioning properly.

Figure A

Figure B

«
...
23
24
25
26
27
...
»

Summary of Contents for 5303

































































Reviews:

No comments

Related manuals for 5303

Brand: TEC Electronics Pages: 16

Brand: Majestic Pages: 8

Brand: RightClick Pages: 8

Brand: NATURE & DECOUVERTES Pages: 9

Brand: HANNspree Pages: 38

Brand: Nemaxx Pages: 72

Brand: Steelmate Pages: 16

Brand: Fusion Pages: 9

Brand: i-box Pages: 56

Brand: Marathon Pages: 13

Brand: Z-Wave Pages: 6

Brand: La Crosse Technology Pages: 10

Brand: BRK electronic Pages: 2

Brand: BRK electronic Pages: 2

Brand: BRK electronic Pages: 19

Brand: Xiaomi Pages: 74

Brand: La Crosse Technology Pages: 20

ITI North American Sensor Carbon Monoxide...

Brand: GE Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands