Avitel 5303 Installation Manual Download

Page: 45 / 64

1-6 PANIC WITH IGNITION ON

: This feature controls whether or not the panic

mode is available with the ignition on. In some states, there are laws prohibiting

a siren sounding in a moving vehicle. This feature makes the system compliant

with these regulations.

1-7 DOOR LOCK PULSE DURATION

: The default setting is 0.8 second door

lock pulses. Some European vehicles, such as Mercedes-Benz and Audi, require

longer lock and unlock pulses to operate the vacuum pump. Programming the

system to provide 3.5 second (2) pulses, accommodates the door lock interface

in these vehicles. (Refer to Tech Tip 1041 on Directechs, for wiring information

regarding Type E door locks interfacing). The 0.4 second (3) pulse is required

on some vehicles where the lock wires also control the windows. The 0.8 sec-

ond pulse causes the windows to open/close when locking or unlocking.

1-8 FORCED PASSIVE ARMING ON

/OFF: To use this feature, passive arming

must be selected in Feature 1-1. When turned on, forced passive arming will

ensure that the system will passively arm, even if a zone is left open or invalid.

Forced passive arming occurs one hour after the ignition is turned off.

1-9 AUTOMATIC ENGINE DISABLE (AED

) ON/

OFF

: AED is a full-time, pas-

sive starter disable that works independently of the security system. When turned

on, the orange, ground-when-armed output (H1/1) will activate 30 seconds

after the ignition is turned off. The LED will flash at half its normal rate when the

ignition is turned off to indicate that AED is active and will interrupt the starter

in 30 seconds. AED does not occur in Valet mode and can be bypassed using

the emergency override procedure. The transmitter can be used to disarm AED,

however, the system must be armed and then disarmed, using the transmitter,

to disarm AED.

1-10 ARMED WHILE DRIVING (AWD) ON

/OFF: In the default setting (Armed

While Driving), the system can be armed with the ignition on. When armed,

the ground-when-armed is not active and the sensors are bypassed. The door

triggers will remain active.

Summary of Contents for 5303





























































Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands

Avitel 5303, Installation Manual

Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands