Avitel 5303 Installation Manual Download | Manualshive

Page: 39 / 64

background image

39

© 2008 Directed Electronics. All rights reserved.

System features learn routine

The System Features Learn Routine dictates how the unit operates. It is possible to

access and change any of the feature settings using the Valet/program switch.

However, this process can be simplified by using the Bitwriter®. Any of the

settings can be changed and then assigned to one of four remote controls. This

feature is called Owner Recognition. Each time that particular remote control is

used to disarm the system, the assigned feature settings will be recalled. Owner

Recognition is only possible when programming the unit via the Bitwriter®.

If programming with the Bitwriter®, the learn routine can be locked or

unlocked. If the learn routine has previously been locked, it must be

unlocked with Bitwriter® - this cannot be done manually with the Valet

switch.

1. Open a door. ((The GREEN wire, h1/8, or

the VIOLET, H1/6 must be connected.)

2. Ignition. Turn the ignition on, and then off.

3. Select menu. Press and hold the Valet/Program

switch. When the LED flashes once and the siren chirps

Menu One has been selected. Continue to hold the

switch until the LED flashes twice and the siren chirps

twice Menu Two has now been selected. Release the

switch after the Menu choice has been selected.

«
...
37
38
39
40
41
...
»

Summary of Contents for 5303

































































Reviews:

No comments

Related manuals for 5303

Brand: aguilera electronica Pages: 2

IntelliGuard 8000

Brand: Clifford Pages: 12

Brand: TFA Pages: 50

Brand: First Alert Pages: 5

Brand: Hanhart Pages: 18

Brand: Avital Pages: 19

Brand: nest Pages: 60

Brand: T-ONE Pages: 2

Brand: Masterbuilt Pages: 20

Brand: CrimeStopper Pages: 1

Brand: CrimeStopper Pages: 7

Brand: CrimeStopper Pages: 12

Brand: Fusion Pages: 8

Brand: Polon-Alfa Pages: 8

Brand: Polon-Alfa Pages: 8

Brand: Toyota Pages: 11

Brand: Connect2Car Pages: 24

CRA54 - Digital Alarm Clock

Brand: Coby Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands