Avitel 5303 Installation Manual Download Page 40

Page: 40 / 64

Choose. Within 10 seconds, press and release

the Valet/Program switch the number of times

corresponding to the feature number you want to

program and then press and hold the switch. (See

Feature Menus. After a second, the LED will flash

to indicate which feature you have accessed. For

example, in Menu Two, groups of eight flashes

would indicate access to the activation pulse setting

(Feature 2-8). The siren will also chirp eight times.

Transmit. The transmitter is used to select the desired

setting. Pressing

��

changes the feature to the LED On

setting (or flashes once for features with more than 2

settings). The siren honks once. Pressing

��

chang-

es the setting to the LED OFF setting (or flashes two

or more times for features with more than 2 settings) .

Release, the Valet/program switch.

You can advance from feature to feature by pressing and releasing the Valet/

Program switch the number of times necessary to get from the feature you just

programmed to the feature you wish to access. For example, in Menu One, if

you just programmed Feature 1-2 and you next want to program Feature 1-3

to off, release the Valet/Program switch. Press and release it once to advance

from Feature 1-2 to Feature 1-3. Then press it once more and hold it. The LED

will flash in groups of 3 and the siren chirps to confirm that you have accessed

Feature 1-3.

The learn routine is exited when:

The door is closed.

•

The ignition is turned on.

•

The Valet/Program switch is pressed too many times.

•

More than 15 seconds elapses between programming steps.

•

Once long siren chirp indicates that the Learn routine has been exited.

Summary of Contents for 5303





























































Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands

Avitel 5303, Installation Manual

Search results

Summary of Contents for 5303

Reviews:

Related manuals for 5303

Brands by name

Popular brands