Avitel 5303 Installation Manual Download | Manualshive

Page: 21 / 64

background image

21

© 2008 Directed Electronics. All rights reserved.

H2/3

VIOLET/BLACK

(-) 200mA PROGRAMMABLE (-) AUX 1 OUTPUT

This wire provides 200 mA programmable output whenever the transmitter but-

tons controlling Aux 1 channel is pressed.

Warning!

Never use this wire to drive anything

but a relay or a low-current input, supplied

output is only 200mA. Connecting directly to

a solenoid, motor, or other high-current device

will cause the module to fail.

H2/4

GREEN/WHITE

FACTORY ALARM REARM OUTPUT

This wire sends a negative pulse every time the remote start shuts down or when

the doors are locked. This can be used to pulse the arm wire of the vehicle’s fac-

tory anti-theft device. Use a relay to send a (-) or (+) pulse to the arm wire.

H2/5

GRAY/BLACK

(-) DIESEL WAIT TO START BULB INPUT

Connect this wire to the wire in the vehicle that sends the signal to turn on the

WAIT-TO-START bulb in the dashboard. In most diesels the wire is negative

(ground turns on the bulb) and the GRAY/BLACK wire can be directly connected

to the wire in the vehicle. If the vehicle uses a positive wire (12V to turn on the

bulb) a relay must be used to change the polarity.

Note:

A 1-amp diode must be installed in line on the factory wire between the

wait-to-start indicator and the ECM. (See the following diagramS for details).

«
...
19
20
21
22
23
...
»

Summary of Contents for 5303

































































Reviews:

No comments

Related manuals for 5303

Brand: Falcon Pages: 8

Brand: SECO-LARM Pages: 2

Brand: Rapid Electronics Pages: 24

RadioLINK Ei168

Brand: EiProfessional Pages: 20

Brand: Techno Line Pages: 102

Brand: Audiovox Pages: 12

Brand: C-KO Pages: 10

Brand: Directed Electronics Pages: 58

Brand: TFA Pages: 2

Brand: Sanyo Pages: 34

Brand: Honeywell Pages: 9

Brand: La Crosse Technology Pages: 14

Brand: Audiovox Pages: 2

Brand: philippi Pages: 6

Brand: VESDA Pages: 50

Brand: Somogyi Pages: 11

Brand: Somogyi Pages: 11

Brand: Fusion Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands