Avaya DEFINITY Server R Manual Download Page 168

Page: 168 / 550

Upgrading R5si/R6si to an Avaya DEFINITY Server R
EPN running Avaya Communication Manager

555-233-115

4-44

Issue 7 November 2003

2. Behind control cabinet A of EPN stack 2:

a. Install a lightwave transceiver on the connector at slot 2A01.

b. Connect a fiber optic cable to the transceiver just installed.

c. Route the cable down the outside of the rear covers and through the

cable manager to the PDS cross-connect facility.

d. Connect the fiber optic cable to the lightguide interface unit.

e. Carefully attach the fiber optic cable (with cable ties) to the rear

covers of the EPN stack.

f. Coil up the surplus fiber optic cable and place the coil in the cable

manager.

Figure 4-11.

Fiber Optic Connections PPN to EPN1

Figure Notes

1. Lightwave Transceiver

2. PPN Carrier B Slot 1B02

3. EPN 1 Carrier A Slot 2A01 (Cabinet

Stack 2)

4. Fiber Optic Cable

5. Fiber Optic Cross-Connect Facility

6. Lightguide Interface Unit (LIU)

7. TX Connector

8. RX Connector

cydf013 CJL102396

RX TX

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands