Avaya DEFINITY Server R Manual Download Page 157

Page: 157 / 550

Install the EPN

Issue 7 November 2003

4-33

555-233-115

Install Cabinet Clips (Systems without
Earthquake Protection)

A cabinet clip is required between each pair of stacked cabinets.

1. At the front of the cabinets, install a cabinet clip between each pair of

cabinets by hooking the clip into the slot of the upper cabinet and snapping
the straight leg of the clip into the slot on the lower cabinet. See

Figure 4-7

Figure 4-7.

Location of Cabinet Clips

Figure Notes

1. Control Cabinet

2. Port Cabinet or Expansion Control Cabinet

3. Port Cabinet

4. Port Cabinet

5. Cabinet Clips

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands