Avaya DEFINITY Server R Manual Download Page 152

Page: 152 / 550

Upgrading R5si/R6si to an Avaya DEFINITY Server R
EPN running Avaya Communication Manager

555-233-115

4-28

Issue 7 November 2003

Reseat DEFINITY LAN Gateway System

1. Reseat the DEFINITY LAN Gateway assembly into the backplane.

Reseat DEFINITY AUDIX System

1. Reseat the DEFINITY AUDIX assembly to its backplane connectors.

Remove Emergency Transfer Ground Wire

1. Remove the ground wire from the emergency transfer unit.

Reboot the System

1. Connect the management terminal or PC to the TERMINAL connector on

the rear of PPN control carrier A.

2. Insert the new Avaya Communication Manager on removable media into

the optical drive.

3. Behind each EPN cabinet, set the circuit breaker to ON.

4. At the PPN power distribution unit, set the main circuit breaker to ON.

The system performs a reset level 4 rebooting process, loading blank
translations from the disk. Rebooting takes 5 to 11 minutes.

5. Type reset system 4 and press

Enter

. This instructs the system to perform

a level 4 reboot, loading the upgraded STS translations from the new
removable media. Rebooting takes 5 to 11 minutes.

6. Log in as craft.

7. After about 2 minutes, type status spe and press

Enter

. The

Standby

Handshake

field must show up before continuing with the upgrade.

8. Type reset spe standby 4 and press

Enter

. This changes the standby SPE

to active and vice versa. This takes about 10 minutes.

9. If the system is high or critical reliability, type status spe and press

Enter

The

Handshake

Refresh

, and

Shadowing

fields show up before

continuing with the upgrade. Also, the

standby side

field shows

in-service. The heartbeat on the standby SPE flashes yellow.

10. Type restore disk

[

spe-a

both

]

full and press

Enter

. This instructs

the system to write the upgraded STS translation information from memory
to the disk(s).

Summary of Contents for DEFINITY Server R







































































































































































































































































































































































































































































































































































Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands

Avaya DEFINITY Server R, Manual

Search results

Summary of Contents for DEFINITY Server R

Reviews:

Related manuals for DEFINITY Server R

Brands by name

Popular brands