Automatic Technology PA1000V1 Page 31 Instruction Manual Download

Page: 31 / 38

Parameters

Door status indicators

Door opener state

Open LED green

Close LED red

Door status
LED yellow

Beeper

Open

Opening

Flashing

Closing

Flashing

Door travel stopped

Flashing

Door obstructed when opening

Flashing

Door obstructed when closing

Flashing

Beeps while
door is moving

Opener overloaded

Alternating flashes

Door in open position with auto-
close mode selected

One second flashes

Mains power interrupted

Rapid flashes

Button

Function

OPERATE

Opens/Stops/Closes the door

CODE SET

Codes a transmitter button for operate function

FORCE MARGIN SET & PLUS (+)

Increases the obstruction force margin setting

FORCE MARGIN SET & MINUS
(-)

Decreases the obstruction force margin setting

FORCE MARGIN SET (then) SET

Reloads the factory set default obstruction force margin setting

Press SET (for 6 sec)

Clears the door limits set positions. Limits then need to be reset.

SET press and hold until all LEDs
are off

Deletes control parameters excluding transmitter storage memory

DOOR CODE press and hold until
DOOR CODE LED starts flashing

Deletes all transmitter storage memory.

SET & DOOR CODE press and
hold until all LEDs are off

Deletes all control parameters and transmitter storage memory.

Diamond PD

Power Drive

: Instruction Manual

PA1000

Instruction Manual (Instructions d’installation)

Summary of Contents for PA1000V1




































Search results

Summary of Contents for PA1000V1

Reviews:

Related manuals for PA1000V1

Brands by name

Popular brands

Automatic Technology PA1000V1, Instruction Manual

Search results

Summary of Contents for PA1000V1

Reviews:

Related manuals for PA1000V1

Brands by name

Popular brands