Automatic Technology PA1000V1 Instruction Manual Download Page 25

Page: 25 / 38

Battery Backup Installation

(Optional)

Battery Back up (optional)

The operator has provision for a Battery Back Up kit that
allows continued operation of the door in the absence of
mains power.

Installation

Disconnect power to the operator.

Remove screws and swing open the cover

(fig 37).

Mount the PCB support with two screws item # 12.

Secure the SBC0-2 Charger Board onto the PCB
support with three (3) screws item #14.
Feed the 2-wire battery harness item # 5 through the

grommet on the base plate and connect to SBCO-2
battery charger board.
Feed charger harness from SBCO-2 battery charger

board to the control board and plug onto the 5 pin
connector marked “SBCO-2” on the control board.
Mount Battery Backup and secure with item 11 and

13.
Connect item 5 and 10 together

(fig 37)

Reconnect power.

Testing Battery Back up

Press either the OPERATE button or transmitter to

activate the operator.
Whilst the door is in motion disconnect mains power -

the operator should continue to operate.

NoTE:

Wait for the door to complete its travel

before proceeding to the next step

Press either the OPERATE button or transmitter to

activate the opener.
Whilst the door is in motion re-connect power. The

door should complete the cycle as normal.

Troubleshooting

If door stops or moves very slowly under battery power,
then the batteries may have little to no charge.

To remedy this connect mains power and leave the batteries
to charge. The batteries may take 24 to 48 hours to reach
their maximum charge capacity.

fig. 37

WARNING:

After the next step the operator

may become active (even when power is off)

due to a residual charge in the batteries.

Diamond PD

Power Drive

: Instruction Manual

PA1000

Instruction Manual (Instructions d’installation)

Summary of Contents for PA1000V1




































Search results

Summary of Contents for PA1000V1

Reviews:

Brands by name

Popular brands

Automatic Technology PA1000V1, Instruction Manual

Search results

Summary of Contents for PA1000V1

Reviews:

Brands by name

Popular brands