AudioCodes mediapack MP-500, User Manual

Page: 398 / 574

SIP User's Manual 398 Document #: LTRT-12801
MP-500 MSBG
Parameter Description
Web: FXO AutoDial Play
BusyTone
EMS: Auto Dial Play Busy
Tone
[FXOAutoDialPlayBusyTone]
Determines whether the device plays a Busy/Reorder tone to the
PSTN side if a Tel-to-IP call is rejected by a SIP error response
(4xx, 5xx or 6xx). If a SIP error response is received, the device
seizes the line (off-hook), and then plays a Busy/Reorder tone to
the PSTN side (for the duration defined by the parameter
TimeForReorderTone). After playing the tone, the line is released
(on-hook).
ƒ
[0] = Disable (default)
ƒ
[1] = Enable
Note: This parameter is applicable only to FXO interfaces.
Web: Hotline Dial Tone
Duration
EMS: Hot Line Tone Duration
[HotLineToneDuration]
Duration (in seconds) of the Hotline dial tone. If no digits are
received during this duration, the device initiates a call to a user-
defined number (refer to Automatic Dialing on page
213 ).
The valid range is 0 to 60. The default is 16.
Note: This parameter is applicable to FXS and FXO interfaces.
Web: Time Before Reorder
Tone [sec]
[TimeBeforeReorderTone]
The delay interval (in seconds) from when the device receives a
SIP BYE message (i.e., remote party terminates call) until the
device starts playing a reorder tone to the FXS phone.
The valid range is 0 to 60. The default is 0.
Note: This parameter is applicable only to FXS interfaces.
Web/EMMS: Reorder Tone
Duration [sec]
[TimeForReorderTone]
The duration (in seconds) that the device plays a Busy or Reorder
tone duration before releasing the line.
The valid range is 0 to 254. The default is 0 seconds.
Typically, after playing a Reorder / Busy tone for the specified
duration, the device starts playing an Offhook Warning tone.
Notes:
ƒ
The selection of Busy or Reorder tone is performed according to
the release cause received from IP.
ƒ
Refer also to the parameter CutThrough.
Web/EMS: Enable Comfort
Tone
[EnableComfortTone]
Determines whether the device plays a Comfort Tone (Tone Type
#18) to the FXS/FXO endpoint after a SIP INVITE is sent and
before a SIP 18x response is received.
ƒ
[0] = Disable (default)
ƒ
[1] = Enable
Note: This parameter is applicable only to FXO/FXS interfaces.
[WarningToneDuration] Defines the duration (in seconds) for which Off-Hook Warning Tone
is played to the user.
The valid range is -1 to 2,147,483,647. The default is 600.
Note: A negative value indicates that the tone is played infinitely.
Web: Play Ringback Tone to
Tel
EMS: Play Ring Back Tone To
Tel
[PlayRBTone2Tel]
Enables the play of the ringback tone (RBT) to the Tel side and
determines the method for playing the RBT.
ƒ
[0] Don't Play = RBT is not played.
ƒ
[1] Play Local = RBT is played to the Tel side of the call when a
SIP 180/183 response is received.
ƒ
[2] Play According to Early Media = RBT is played to the Tel
side only if a 180/183 response without SDP is received. If
180/183 with SDP message is received, the device cuts through
the voice channel and doesn't play RBT (default).